Sharp CP-SR421 User Manual Page 85
- Page / 404
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
4. STARTUP
4 - 6
(5) Stop
If any of the following situations occurs, the servo amplifier suspends the running of the servo motor and
brings it to a stop.
Refer to section 3.10. for the servo motor with an electromagnetic brake.
Operation/command Stopping condition
Servo-off command The base circuit is shut off and the servo motor coasts.
Ready-off command
The base circuit is shut off and the dynamic brake operates to
bring the servo motor to a stop.
Servo system
controller
Forced stop command
The servo motor decelerates to a stop with the command. [AL.
E7 Controller forced stop warning] occurs.
Alarm occurrence
The servo motor decelerates to a stop with the command. With
some alarms, however, the dynamic brake operates to bring the
servo motor to a stop. (Refer to section 8. (Note))
Servo amplifier EM2 (Forced stop 2) off
The servo motor decelerates to a stop with the command. [AL.
E6 Servo forced stop warning] occurs. EM2 is the same signal as
EM1 in the torque control mode. EM2 has the same function as
EM1 in the torque control mode. Refer to section 3.5 for EM1.
STO (STO1, STO2) off
The base circuit is shut off and the dynamic brake operates to
bring the servo motor to a stop.
Note. Only a list of alarms and warnings is listed in chapter 8. Refer to "MELSERVO-J4 Servo Amplifier Instruction
Manual (Troubleshooting)" for details of alarms and warnings.
4.3 Switch setting and display of the servo amplifier
Switching to the test operation mode, deactivating control axes, and setting control axis No. are enabled with
switches on the servo amplifier.
On the servo amplifier display (three-digit, seven-segment LED), check the status of communication with the
servo system controller at power-on, and the axis number, and diagnose a malfunction at occurrence of an
alarm.
4.3.1 Switches
WARNING
When switching the axis selection rotary switch (SW1) and auxiliary axis number
setting switch (SW2), use an insulation screw driver. Do not use a metal screw
driver. Touching patterns on electronic boards, lead of electronic parts, etc. may
cause an electric shock.
POINT
Turning "ON (up)" all the control axis setting switches (SW2) enables an
operation mode for manufacturer setting and displays "off". The mode is not
available. Set the control axis setting switches (SW2) correctly according to this
section.
Cycling the main circuit power supply and control circuit power supply enables
the setting of each switch.
- MR-J4-_B 1
- 6DIHW\,QVWUXFWLRQV 2
- :$51,1* 2
- &$87,21 2
- &$87,21 3
- ',6326$/2):$67( 7
- (Note 4) 17
- (2) MR-J4-700B 18
- [Pr. PC09], [Pr. PC10] 22
- MR-J4-10B 23
- Inside of the display cover 24
- Bottom face 24
- Chapter 24
- 1 - 10 25
- (2) MR-J4-350B 25
- Front cover 29
- Setting tab 29
- Next servo amplifier 30
- CN1A or cap 30
- 1 - 16 31
- 1 - 17 32
- (3) MR-J4-500B 32
- Servo system controller or 33
- 40 mm or more 35
- 2. INSTALLATION 36
- శࠦ࠼ㇱ ࠤࡉ࡞ㇱ 37
- 3. SIGNALS AND WIRING 44
- 3 s to 4 53
- If polarity of diode is 70
- Servo motor speed 76
- 6,*1$/6$1':,5,1* 79
- 4. STARTUP 81
- Servo amplifie 82
- Servo moto 82
- ᓮゲήലࠬࠗ࠶࠴ 86
- Alarm No 89
- (2 digits) 89
- Flickering 90
- 67$5783 91
- SW2-1ࠍ"ࠝࡈ(ਅ)"ߦ⸳ቯ 97
- 5. PARAMETERS 100
- 3$5$0(7(56 124
- [Pr. PC24] 134
- 0 r/min 134
- (0 mm/s) 134
- 6. NORMAL GAIN ADJUSTMENT 146
- Speed loop gain setting 159
- Speed [r/min] 163
- Model loop gain setting 163
- Notch depth 165
- Notch frequency 167
- Has vibration or unusual 168
- [Pr.PB23] 169
- ゲᝄᛥࡈࠖ࡞࠲ㆬᛯ 169
- 1: ࡑ࠾ࡘࠕ࡞⸳ቯ 169
- Manual setting 170
- Disabled 170
- Low-pass filter selection 170
- Setting value 171
- Has vibration of workpiece 172
- Motor-side vibration 174
- (droop pulses) 174
- Position 175
- Load side 175
- Setting 176
- Frequency 176
- 7 - 21 184
- (b) Switching timing chart 184
- CAUTION 187
- (Warning) 189
- Instantaneous power 190
- 8. TROUBLESHOOTING 192
- 287/,1('5$:,1*6 200
- 205
- $SSUR[ $SSUR[ 205
- $SSUR[ 205
- / /7( 206
- 208
- 10. CHARACTERISTICS 210
- Operating 211
- Air flow 213
- Time constant IJ [ms] 215
- WARNING 218
- Cautions 218
- Servo amplifier 221
- MR-D05UDL3M-B 221
- 2.2 ± 0.07 222
- Protective tube 223
- Unbalance torque 225
- Positive 227
- Negative 227
- [Unit: mm] 231
- N/- P/+ PR 237
- 237
- (Note 1) 244
- Power supply 246
- Environment 246
- 2CR17335A WK17 250
- 6V 1650mAh 250
- (Note 2) 254
- CR-10201 259
- Approx. 22.5 261
- Approx. 65 261
- Leakage current [mA] 264
- 28.5 ± 1 28 ± 1 269
- 4.5 ± 0.5 269
- &RYHU 274
- /RFNLQJSDUW 274
- 05%$79 274
- :$51,1* 276
- 86,1*672)81&7,21 277
- 67272)% 279
- 672&20 279
- 72)&20 279
- WARNING 288
- Linear servo motor 290
- Installation and wirin 292
- Absolute position linear 292
- Incremental linear encoder 292
- 14 - 7 294
- [Pr. PL03] 295
- [Pr. PL02] 295
- Has [AL. 27 Initial magnetic 296
- occurred? 296
- 14 - 10 297
- Servo-off status 298
- During the magnetic 298
- (servo-on status) 298
- [Pr.PL01] 301
- Position detection method 302
- [Pr. PL08] 302
- Stop interval [pulse] 303
- 1048576 (initial value) 303
- 1048576 pulses × n 306
- SW2-1ࠍ"ࠝࡦ()"ߦ⸳ቯ 308
- Differ 310
- ࠨࡏࡠ࠶ࠢᤨ 313
- Servo system controller 319
- 15 - 5 322
- 15.3.1 Startup procedure 322
- 15 - 8 325
- [Pr.PL08] 329
- 0: Position detection method 329
- [Pr.PL04] 332
- EM1 (Forced stop 1) 336
- 16 - 2 339
- Semi closed loop control 340
- Fully closed loop control 340
- SSCNET III/H controller 341
- Load-side encoder 342
- Do as necessary 345
- Operation mode 346
- Linear encoder 347
- Linear encoder head 347
- Geared servo motor 347
- Pulley diameter 348
- Servo motor-side cumulative 349
- Droop pulses 350
- Linear encoder home position 351
- Proximity dog signal 352
- JOG operation 352
- Servo motor s 355
- [Pr. PE03] 357
- 'ZRNCPCVKQP 359
- 16 - 23 360
- APPENDIX 362
- 24 V DC 365
- EMG stop 370
- 2.3mm 0.05mm 384
- 40 mm or longer 388
- 2) 3) 4) 1) 392
- ࠕ࠽ࡠࠣࡕ࠾࠲ch1ജㆬᛯ 394
- (MO1-LG㑆ߦജߔࠆାภ) 394
- REVISIONS 399
- MITSUBISHI ELECTRIC 404
Related products and manuals for Unknown Sharp CP-SR421
Unknown Sharp MZ-1F11 Instruction Manual
(13 pages)
(13 pages)
Unknown Sharp PW-E410 User Manual
(76 pages)
(76 pages)
Unknown Sharp AN-CM270 User Manual
(24 pages)
(24 pages)
Unknown Sharp MD-MX30W User Manual
(20 pages)
(20 pages)
Unknown Sharp SJ-D51J Instruction Manual
(4 pages)
(4 pages)
Unknown Sharp CD-ES222H User Manual
(37 pages)
(37 pages)
Unknown Sharp CD-SW330 User Manual
(104 pages)
(104 pages)
Unknown Sharp XL-MP100H User Manual
(41 pages)
(41 pages)
Unknown Sharp LC-32SB24U User Manual
(10 pages)
(10 pages)
Unknown Sharp ND-240R1J User Manual
(40 pages)
(40 pages)
Unknown Sharp SJ-F800SPBK User Manual
(12 pages)
(12 pages)
Unknown Sharp XL-3000V User Manual
(28 pages)
(28 pages)
Unknown Sharp XL-E25H User Manual
(45 pages)
(45 pages)
Unknown Sharp SJ-PK70M Owner's Manual
(112 pages)
(112 pages)
Unknown Sharp SJ-F624ST User Manual
(12 pages)
(12 pages)
Unknown Sharp ORGANIZER Link4 User Manual
(15 pages)
(15 pages)
Unknown Sharp XL-MP333H User Manual
(49 pages)
(49 pages)
Unknown Sharp SJ-F602SP User Manual
(12 pages)
(12 pages)
Unknown Sharp VC-FH300SM User Manual
(38 pages)
Unknown Sharp XL-MP9H Specifications
(43 pages)
(43 pages)
© 2020, manymanuals.com. All rights reserved. | 0.244 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals