Sharp CP-SR421 User Manual download pdf (Page 45)

3. SIGNALS AND WIRING

3 - 4

(1) For 3-phase 200 V AC to 240 V AC power supply of MR-J4-10B to MR-J4-350B

(Note 7)

ALM

DICOM

DOCOM

CN3

(Note 5)

24 V DC

Malfunction (Note 4)

RA1

3-phase

200 V AC to

240 V AC

Servo amplifier

P+

L11

L21

N-

(Note 1)(Note 10)

(Note 2)

CNP1

CNP3

CNP2

Servo motor

Motor

Encoder

CN2

(Note 3)

Encoder

cable

(Note 6)

(Note 4)

Malfunction

RA1

OFF

EMG stop switch

CN3

(Note 5) Forced stop 2 EM2

DOCOM

CN8

(Note 9)

Short-circuit connector

(Packed with the servo amplifier)

(Note 8)

Main circuit power supply

MCCB

Note 1.

10.

Always connect P3 and P4 terminals. (factory-wired) When using the power factor improving DC reactor, refer to section

11.1. Use either the power factor improving DC reactor or the power factor improving AC reactor.

Always connect P+ and D. (factory-wired) When using the regenerative option, refer to section 11.2.

For the encoder cable, use of the option cable is recommended. For connecting servo motor power wires, refer to Servo

Motor Instruction Manual (Vol. 3).

If disabling ALM (Malfunction) output with the parameter, configure up the power supply circuit which switches off the

magnetic contactor after detection of alarm occurrence on the controller side.

This diagram is for sink I/O interface. For source I/O interface, refer to section 3.8.3.

For connecting servo motor power wires, refer to each Servo Motor Instruction Manual (Vol. 3).

Use a magnetic contactor with an operation delay time (interval between current being applied to the coil until closure of

contacts) of 80 ms or less. Depending on the main circuit voltage and operation pattern, bus voltage decreases, and that

may cause the forced stop deceleration to shift to the dynamic brake deceleration. When dynamic brake deceleration is not

required, slow the time to turn off the magnetic contactor.

Configure up a circuit to turn off EM2 when the main circuit power is turned off to prevent an unexpected restart of the servo

amplifier.

When not using the STO function, attach a short-circuit connector supplied with a servo amplifier.

When wires used for L11 and L21 are thinner than wires used for L1, L2, and L3, use a molded case circuit breaker. (Refer

to section 11.10.)

1 2 ... 40 41 42 43 44 45 46 47 48 49 50 ... 403 404

Comments to this Manuals

No comments

Trekstor 75816 Datenblatt (2 Seiten)

Marke: Trekstor | Kategorie: MP3/MP4 players | Größe: 0.61 MB |

Inhaltsverzeichnis

MP3Player

TECHNICAL DATA

Weitere Produkte und Handbücher für MP3 / MP4-Player Trekstor

Modelle	Dokumententyp
101045	Datenblatt Trekstor i.Beat mood FM 2 GB, 2 Seiten
71810	Datenblatt Trekstor 1GB i.Beat cebrax FM, 2 Seiten
71816	Datenblatt Trekstor i.Beat cebrax 2.0, 2 Seiten
73810	Datenblatt Trekstor 2GB i.Beat censo, 2 Seiten
74916	Datenblatt Trekstor i.Beat cody 4GB, 2 Seiten
74412	Datenblatt Trekstor i.Beat emo 2GB, 2 Seiten
193354	Datenblatt Trekstor Vibez 12 GB, 2 Seiten
4016998729249	Datenblatt Trekstor Vibez 8GB, 2 Seiten
4016998219443	Datenblatt Trekstor i.Beat organix [FM], 2 Seiten
74612	Datenblatt Trekstor US5 1GB, 2 Seiten
173824	Datenblatt Trekstor i.Beat motion 2 GB, 2 Seiten
74312	Datenblatt Trekstor i.Beat sonix 2GB, 2 Seiten
4016998720109	Datenblatt Trekstor i.Beat vision DM 1 GB, 2 Seiten
173789	Datenblatt Trekstor i.Beat sweez FM 2 GB silver, 2 Seiten
71508	Datenblatt Trekstor i.Beat sweez FM, 512MB, Silver, 2 Seiten
74212	Datenblatt Trekstor i.Beat motion 4GB, 2 Seiten
21747ROT	Datenblatt Trekstor i.Beat organix FM 2 GB silver, 2 Seiten
74810	Datenblatt Trekstor i.Beat censo 2 GB, 2 Seiten
75916	Datenblatt Trekstor i.Beat nova 8GB black, 2 Seiten
4016998218491	Datenblatt Trekstor i.Beat organix 2.0 silver, 2 Seiten