Sharp FO-6700 Service Manual Page 40

  • Download
  • Add to my manuals
  • Print
  • Page
    / 192
  • Table of contents
  • TROUBLESHOOTING
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 39
FO-6700U
FO-67DL
00: Manual
01: Automatic 1
10: Automatic 2
11: Except the above
To select detail paper in the first prior-
ity cassette in accordance with setting
by SW65 3-8 and SW65 1-3. If the de-
tail paper in the first priority cassette
runs short, the second priority cassette
will be used.
To automatically select detail paper with
optimum size among the first to third
priority cassettes in accordance with
setting by SW65 3-8 and SW65 1-3.
The optimum paper is selected by every
page. If all the cassettes have the same
size paper, paper will be selected ac-
cording to the cassette priority.
To automatically select detail paper with
optimum size among the first to third
priority cassettes in accordance with
setting by SW65 3-8 and SW65 1-3. At
the start of printing, the optimum pa-
per is adopted only for the first page.
Thereafter the same cassette selected
for the first page will be used from the
second page and after. If all the cas-
settes have the same size paper, pa-
per will be selected according to the
cassette priority.
01: the same setting as in the case of
Automatic 1
2 – 32
SW62 No. 3 Reserved
Set to "1".
SW62 No. 4 Reserved
Set to "0".
SW62 No. 5, No. 6 Ringer volume
Ringer volume:
The calling sound volume of CI signal receiving is set.
SW62 No. 7, No. 8 Reserved
Set to "0".
SW63 No. 1 Reserved
Set to "0".
SW63 No. 2 PC I/F mode
The interface with the personal computer is selected.
SW63 No. 3 ~ No. 8 Reserved
Set to "0".
SW64 No. 1 Header registration
When setting this switch to "1", registering senders is protected.
SW64 No. 2 Reserved
Set to "0".
SW64 No. 3 Continuous serial polling
Turns ON/OFF the continuous polling function.
SW64 No. 4, No. 5 Time interval for continuous serial polling
Used to set the interval time for continuous serial polling. Normally set
to no interval (0 minute).
SW64 No. 6, No. 7 Reserved
Set to "0".
SW64 No. 8 Quick on-line function
It is selected whether auto dial call is activated in the memory input
mode when one document is completely read or when all pages are
completely read.
SW65 No. 1, No. 2 Cassette selection
To set selective modes for detail paper cassettes of the printer.
SW49 No. 5 Reserved
Set to "1".
SW49 No. 6 ~ No. 8 Reserved
Set to "0".
SW50 No. 1, No. 2 DTMF detection time
Used to set detect time of DTMF (Dual Tone Multi Frequency) used in
remote reception (5 ). The longer the detection time is, the error
detection is caused by noises.
SW50 No. 3 ~ No. 8 Reserved
Set to "0".
SW51 No. 1 ~ No. 3 Reserved
Set to "0".
SW51 No. 4 ~ No. 6 Busy tone detection frequency
To select frequency range of signals to be detected as Busy Tone.
SW51 No. 7, No. 8 Reserved
Set to "0".
SW52 No. 1 ~ No. 8 Reserved
Set to "0".
SW53 No. 1 ~ No. 8 Reserved
Set to "0".
SW54 No. 1 ~ No. 8 Reserved
Set to "0".
SW55 No. 1 ~ No. 8 Reserved
Set to "0".
SW56 No. 1 ~ No. 8 Reserved
Set to "0".
SW57 No. 1 ~ No. 8 Reserved
Set to "0".
SW58 No. 1 ~ No. 8 Reserved
Set to "0".
SW59 No. 1 ~ No. 8 Reserved
Set to "0".
SW60 No. 1 ~ No. 8 Reserved
Set to "0".
SW61 No. 1 F.A.S.T (RMS) mode
Used to determine a function of remote maintenance system (F.A.S.T).
SW61 No. 2 F.A.S.T (RMS) line
The line where the F.A.S.T. function is set.
SW61 No. 3 Verification stamp
End stamp:
It is set whether the red round mark is stamped at the bottom margin of
the document of every page in the memory input mode and document
sending mode or not.
SW61 No. 4 Day light saving
The day light saving function ON/OFF is set.
SW61 No. 5, No. 6 Key buzzer volume
Key buzzer volume:
The sound volume of key inputting buzzer and other buzzers is set.
SW61 No. 7, No. 8 Reserved
Set to "0".
SW62 No. 1, No. 2 Speaker volume
Speaker volume:
The sound volume of the speaker in the on-hook mode is set.
Page view 39
1 2 ... 35 36 37 38 39 40 41 42 43 44 45 ... 191 192

Comments to this Manuals

No comments