Sharp FO-6700 Service Manual download pdf (Page 13)

FO-6700U

FO-67DL

9) Signal send mode

After shift to the mode, press the START key, and the signals will be

transmitted in the following sequence.

It can be used to check the modem and so on.

[ 1] No signals

[ 2] 4800BPS (V27ter)

[ 3] 14400BPS (V. 33)

[ 4] 12000BPS (V. 33)

[ 5] 14400BPS (V. 17)

[ 6] 12000BPS (V. 17)

[ 7] 9600BPS (V. 17)

[ 8] 7200BPS (V. 17)

[ 9] 9600BPS (V. 29)

[10] 7200BPS (V. 29)

[11] 4800BPS (V27ter)

[12] 2400BPS (V27ter)

[13] 300BPS (FLAG)

[14] 2100Hz (CED)

[15] 1100Hz (CNG)

10) Comm. check mode

Turn on the Line Monitor.

Turn off the Cover Sheet Function.

Set Line Equivalence at 0 km.

After the check, it is necessary to be sure to return the aforementioned

soft switches into the initial state.

(Clear the memory with the diagnosis.)

11) Memory clear mode

Clear the back-up memory to initialize the soft switches.

The Flash Memory will be initialized. Then, the initialized list be output.

12) Flash Memory check

The Flash Memory is checked.

The ordinary memories (ROM, SRAM, DRAM) are checked in the ROM

& RAM check process. The write/read test is taken every block to print

the result.

When an error occurs, the following error buzzer will sound.

During operation of this diagnosis, dual operation is not possible at all.

If this is excessively repeated, it will shorten the life of the flash memory.

13) All FAX/TEL. entry mode

The function is used to simplify the registration of FAX/TEL No. during

aging.

The diagnosis mode is activated. If anything is not registered in the

Rapid number 01 or any program or group is not registered, it will

pass the diagnosis without doing anything.

The FAX/TEL number (including the substitutive destination) of the

Rapid number 01 is copied to the Rapid numbers 02 thru 48.

FAX number of the Rapid number 01 is copied to SPEED key numbers

001 thru 200.

If any chain dial is not in the Rapid number, the Rapid numbers 02

thru 48 and SPEED key numbers 001 thru 200 are registered in the

group number 01.

If any chain dial is set, the group will be not produced but the chain

dial setting alone of the Rapid number 01 will be reset.

(In all others except the Rapid number 01, the chain dials will be

continuously set as they are.)

(16th and subsequential letters of the destination name registered in the

Rapid number 01 will be discarded.)

Personal book 00 to 30 are set up. (Their PASSCODE to be regis-

tered are 0000 to 0030, and the NAME are "BOOK00" to "BOOK

30".)

The registration information of RAPID01 is copied to RAPID02 to 48

of each book.

The registration information of RAPID01 is copied to SPEED001 to

016 of each book.

When the chain dial is not set up in RAPID01, specify RAPID02 to 48

and SPEED001 to 016 in GROUP1 of each book.

14) Dept. passcode

The department passcode list is printed.

15) Conf. passcode

The confidential passcode list is printed.

Differing from printing of one box alone soon after registration, the con-

fidential passcodes of all boxes are printed.

16) Print hold code

The print lockout passcode No. is printed.

17) Memory set mode

The set and dump list of the memory content is output.

• The address (8 digits (P) generally including the bank information is

input, and the data of 2 digits is continuously input.

Inputting is done in the hexadecimal mode. The ten-key is used for 0

thru 9, and the alphabetic keys A (RAPID 01 thru 06) are used for A

thru F.

• During data inputting, the address can be moved forward and back-

ward one byte by one byte with " " and "#". (The address prior to the

address 0 is looped as the maximum address.)

• The Validity of the address is not checked. Accordingly, writing/ read-

ing operations are possible in the address of the memory not as-

signed, the address of ROM and so on.

(However, as practical, writing is not done, and the data content runs

short each reading.)

Though writing is possible in the flash memory, a little time is re-

quired.

It is also necessary to take care that the life of the flash memory is

excessively shortened if much data is written in the flash memory.

Since it may run away depending the written content, take minute

care for the writing address.

• When the REPORT key is input, the memory dump list is produced

from the displayed address (here, it is limited at the 16-byte bound-

ary address (address with end 0) which does not exceed the speci-

fied address and is just in front.). The dump list is output to a maxi-

mum of 99 pages. If any data of one page can be repeatedly devel-

oped and printed, the list is sufficient. But it is not desired that the

content of plural pages are developed in the memory once and are

then printed. If the STOP key is pressed, it will pass to the diagnosis

after the page which is now being printed is completed printed.

If the address exceeds the maximum address, it will return to the

address 0 and printing will be continued.

18) Stamp aging

Diag mode is left though it doesn’t have this function.

Rapid key RXX XX : Rapid number

SPEED key SXXX XXX

: Speed key number

Number of buzzer sounds Check device

9 times <Short sounds> Flash memory (Option)

2 – 5

1 2 ... 8 9 10 11 12 13 14 15 16 17 18 ... 191 192

Comments to this Manuals

No comments

Sharp FO-6700 Service Manual Page 13

Comments to this Manuals

Related products and manuals for Fax machines Sharp FO-6700