Sharp FO-6700 Service Manual download pdf (Page 35)

FO-6700U

FO-67DL

• Soft switch function description

SW1 No. 1 ~ No. 4 Recall interval

Choice is made for a recall interval for speed and rapid dial numbers.

Use a binary number to program this. If set to 0 accidentally, 1 will be

assumed.

SW1 No. 5 ~ No. 8 Recall times

Choice is made as to how many recall times should be made. Use a

binary number to program this.

SW2 No. 1 Dial mode

Switch the type according to the telephone circuit connected to the fac-

simile.

0: PULSE DIAL

1: TONE DIAL

SW2 No. 2 Receive mode

Auto/manual receiving mode is set.

SW2 No. 3 ECM mode

Used to determine ECM mode function.

SW2 No. 4 Reserved

Set to "0".

SW2 No. 5 Polling security

This switch is employed to enable or disable the polling operation using

the ID code verification function, in order to prevent unauthorized polling

operation.

SW2 No. 6 Auto cover sheet

When "1" (=YES) is selected, the cover sheet is automatically sent after

transmission of the original to notify the receiver of the number of origi-

nal sheets transmitted.

SW2 No. 7 JUNK-FAX function in manual reception

It is set whether JUNK-FAX is functioned in the manual receiving mode

or not.

SW2 No. 8 JUNK-FAX function

This function is used to receive data from a specific remote machine

(station registered in entry mode). It is the function that refused a recep-

tion in the case that TSI of remote machine matched with fax number of

the station registered.

0: No

1: Yes

SW3 No. 1 ~ No. 4 Number of rings for auto-receive

(0: No ring receive)

When the machine is set in the auto receive mode, the number of rings

before answering can be selected. It may be set from one to nine rings

using a binary number. If the soft switch was set to 1, a direct connection

is made to the facsimile. If it was set to 0 accidentally, receive ring is set

to 1. If it was above 9, receive rings are set to 9.

SW3 No. 5 ~ No. 8 Switch to auto-receive from manual receive

(0: No switch)

This setting allows machine to switch from manual to Auto Receive mode.

Setting this number to 0 forces machine to stay in Manual receive mode.

Entering the binary number 0 forces the machine to remain in the manual

answer mode. If a number between 1 and 9 is entered, the machine will

go into the answer mode after the given number of rings. However, it can

be used as an ordinary telephone if the handset is taken off the hook

before this programmed number is finished. If entry of a number above 9

by accident, it will be set to 9. In this case, it must be corrected to the

proper number.

SW4 No. 1 ~ No. 3 Communication results printout

It is possible to obtain communication results after each transaction.

Normally, the switch is set (No. 1: 0, No. 2: 0, No. 3: 1) so that the com-

munication result is produced only a communication error is en-coun-

tered. If No. 1 was set to 1, No. 2 was set to 1 and No. 3 was set to 0, the

communication result will be produced every time a communication is

done, even if the communication was successful.

If No. 1 was set to 0, No. 2 to 1 and No. 3 to 0, the communication result

will be produced every transmission.

Setting No. 1 to 1 No. 2 to 0 and No. 3 to 0 will disable this function. No

transaction report will be printed.

If No. 1 was set to 0, No. 2 to 0 and No. 3 to 0, the communication result

is produced only after a timer and memory transmission or when a com-

munication error is encountered.

SW4 No. 4 Image addition function to the communication result

table (for memory transmission only)

Used to set addition of sending image to the communication result table.

SW4 No. 5 Reserved

Set to "0".

SW4 No. 6 TEL billing code function

When set to "1", the TEL billing code function is enabled.

SW4 No. 7 Billing code position

When set to "1", the billing code is delivered before dialing the remote

number. When set to "0", the billing code is delivered after dialing.

SW4 No. 8 Multi-TTI feature

When this switch is set to "1", Multi TTI function is enabled.

SW5 No. 1 Time display format

When this switch is set to "0", time is displayed in 12-hour system.

When set to "1", 24-hour system.

SW5 No. 2 Date display format

Used to select date display/print formats.

0: DAY-Month-Year

1: Month-DAY-Year

SW5 No. 3 Header print

When it is set at 0, sender’s name, sending page number and so on are

automatically printed in the recording paper on the receiving side during

transmission. Thus, the sender can be known on the receiving side.

0: Applied.

1: Not applied.

SW5 No. 4 Footer print

When set to "1", the date of reception, the sender machine No., and the

page No. are automatically recorded at the end of reception.

SW5 No. 5 Relay data output

0: Output ON

1: Output OFF

SW5 No. 6 Substitute reception

Selection of substitute reception in the case of recording paper ex-hausted

or paper jam. If set to "NO", auto receive is disabled even when the

receive memory is ready to receive.

Substitute reception is not performed even during receive operation.

SW5 No. 7 Substitute reception conditions

Selection of substitute reception according to existence of TEL number

from transmitting side. Initial setting allows substitute reception without

CSI. If set to "no", the receiver cannot receive any documents

SW5 No. 8 CSI transmission

CSI signal contains the sender’s phone number registered in the ma-

chine. If this switch is set to "1", no sender’s name will be printed at the

receiving side.

2 – 27

1 2 ... 30 31 32 33 34 35 36 37 38 39 40 ... 191 192

Comments to this Manuals

No comments

Sharp FO-6700 Service Manual Page 35

Comments to this Manuals

Related products and manuals for Fax machines Sharp FO-6700