Sharp AN-CM250 Specifications Page 35
- Page / 97
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Image Projection
Basic Procedure
Connect the required external equipment to
the projector before operating the following
procedures.
Info
•
The language preset at the factory is English.
If you want to change the on-screen display
to another language, reset the language ac-
cording to the procedure on page
36
.
1 Plug the power cord into the
wall outlet.
• The power indicator illuminates red, and
the projector enters standby mode.
2 Press on the remote control
or
on the projector.
• The power indicator illuminates blue.
After the lamp indicator illuminates, the
projector is ready to start operation.
Note
• The lamp indicator illuminates, indi-
cating the status of the lamp.
Blue: The lamp is ready.
Blue blinking: The lamp is
warming up.
Red:
The lamp should be replaced.
• If the projector is put into the
standby mode and immediately
turned on again, the lamp indicator
may take some time to illuminate.
• When controlling the projector using
RS-232C commands from a com-
puter, wait for at least 30 seconds
after the power has been turned on,
and then transmit the commands.
-34
INPUT
button
ON button
STANDBY
button
MENU button
", ',\, | buttons
ENTER
button
ON button
INPUT
buttons
", ', \, |
buttons
MENU button
ENTER
button
STANDBY
button
Lamp indicator
Power indicator
XV_Z12000_E_US_p33_41.p65 03.9.24, 1:59 PM34
- SHARP CORPORATION 1
- Introduction 2
- WARNING: 3
- PRODUCT DISPOSAL 3
- INFORMATION 3
- Declaration of Conformity 3
- Contents 4
- Easy to Use Functions 5
- Appendix 5
- IMPORTANT SAFEGUARDS 6
- SharpVision Manager 9
- Quick Guide 10
- Part Names 11
- Projector (Rear View) 12
- Remote Control (Front View) 13
- Remote Control (Top View) 13
- Using the Remote Control 14
- 3 Insert the lower tab of the 14
- Accessories 15
- Connections and Setup 16
- Before Connecting 17
- Connecting the Power 17
- Connecting to Video Equipment 18
- Connecting to 19
- Component Video 19
- Equipment Using a 19
- Component Cable 19
- (INPUT 1 or 2) 19
- 1 Connect a DVI to HDMI cable 22
- Connecting to a Computer 23
- Using the DVI to 15-pin 23
- D-sub Adaptor and the 23
- RGB Cable (INPUT 5) 23
- Connecting to a Com 24
- Cable (INPUT 5) 24
- “Plug and Play” function 25
- 1 Connect an RS-232C cable to 26
- Connecting the Remote 27
- Control to the Projector 27
- 2 Remove your hands from the 28
- 2 Zooming is adjusted by mov 29
- Using the Lens Shift 30
- Audience 31
- Projection using a mirror 33
- Ceiling-mount setup 33
- Basic Operation 34
- Image Projection 35
- 3 Press , , , or 36
- 1 Press 37
- 4 Press 37
- 1 Press on the remote control 38
- UNDO button 40
- Menu Bar Items 41
- Using the Menu Screen 43
- 2 Press 44
- 3 Press 44
- 4 Press 44
- 5 Press 44
- 5 Press 46
- 6 Press 46
- 7 Press 46
- Adjusting the Picture 47
- Adjusting Image Prefer 48
- Selecting the Gamma 48
- Position 48
- Selecting the C.M.S 49
- Special Settings 49
- Emphasizing the 51
- Contrast 51
- Reducing Image Noise 51
- Emphasizing Outlines 52
- Resetting All Adjust 52
- Adjusting the Gamma 53
- Selecting the Target 55
- Resetting User-Defined 57
- Color Settings 57
- Overview of All Color 57
- Settings 57
- Adjusting Computer Images 58
- Selecting Adjustment Settings 59
- Special Mode Settings 59
- Checking the Input Signal 60
- Auto Sync Adjustment 60
- Auto Sync Display 61
- Function 61
- Switching the Picture 63
- Display Using Different 63
- Input Signals 63
- COMPUTER 65
- Switching HIGH 66
- BRIGHTNESS MODE/ 66
- HIGH CONTRAST MODE 66
- Digital Shift Function 67
- Subtitle Setting 67
- LED Off Function 68
- Setting On-screen Display 69
- Selecting the Signal Type 70
- Setting the Video System 71
- Setting a Background Image 71
- Selecting the Economy Mode 72
- Selecting the Transmis 73
- Automatic Power Off 73
- Setting the Projection 74
- Overview of All Menu 75
- Neutral detergent 77
- Cleaning 77
- Cleaner 78
- Maintenance Indicators 79
- Regarding the Lamp 81
- 1 Press 82
- 2 Disconnect the power cord 82
- 3 Remove the lamp unit cover 82
- 4 Remove the lamp unit 83
- 5 Insert the new lamp unit 83
- 6 Attach the lamp unit cover 83
- 1 Connect the power cord 83
- 2 Reset the lamp timer 83
- Connecting Pin Assignments 84
- PC control 85
- Communication conditions 85
- Basic format 85
- Commands 85
- Computer Compatibility Chart 89
- Troubleshooting 90
- Specifications 92
- Dimensions 93
- Glossary 94
- VALID IN USA ONLY 96
- Consumer Electronics Products 97
Related products and manuals for Data projectors Sharp AN-CM250
Data projectors Sharp XV-Z10E Specifications
(73 pages)
(73 pages)
Data projectors Sharp CMS-R600X User Manual
(70 pages)
(70 pages)
Data projectors Sharp IQ-8000 Specifications
(10 pages)
(10 pages)
Data projectors Sharp AN-CM270 User Manual
(18 pages)
(18 pages)
Data projectors Sharp PG-D2500X Setup Guide
(77 pages)
(77 pages)
Data projectors Sharp CD-E250E User Manual
(16 pages)
(16 pages)
© 2020, manymanuals.com. All rights reserved. | 0.728 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals