Sharp AR-C240P Specifications Page 138
- Page / 196
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
138 /
8 Color detaches.
• Is the LED head dirty?
YES Clean the LED head.
▼
• NO Is the LED head assembly connected to the connection board (Y73 PWB) properly?
NO Check the connection cable between the LED head and connection board, then connect
properly.
▼
• YES Is +5V output to the following HEADPOW connector pins on the connection board (Y73
PWB)?
+5V: Pin 1, 2, 3, 4, 5, 6
• YES Is +5V output to the each LED head assemblies on the connection board (Y73 PWB)?
3 pin for YPOW connector : LED head assembly - yellow
3 pin for MPOW connector : LED head assembly - magenta
3 pin for CPOW connector : LED head assembly - cyan
3 pin for KPOW connector : LED head assembly - black
NO Replace the connection board (Y73 PWB).
▼
• YES Check the cable connections, then replace the LED head assembly.
▼
• NO Check the cable connections, then replace the low-voltage power unit. Did the printer
recover?
YES End.
▼
• NO Is 34V output to the power connector on the engine board (K7N PWB)?
+34V: Pin 12, 13, 14
NO Check the cable connections, then replace the low-voltage power unit.
▼
• YES Is 34V output to the HVOLT connector pin 2 on the engine board (K7N PWB)?
NO Replace the engine board.
▼
• YES Check the cable connections, then replace the high-voltage power unit or belt cassette
assembly.
YES End.
▼
• NO Is the I/D unit terminal connected properly to the contact assembly. (See Fig. 5-3)
NO Connect the I/D unit terminal to the contact assemblyproperly .
▼
• YES Replace the image drum.
Note:
1. Remove EEPROM from the old board and set it on the new board upon replacing the
engine board (K7N PWB).
2. If EEPROM is not replaced, refer to section 3.2.2.
- AR -C 240P 1
- CONTENTS 3
- 1. CONFIGURATIONS 6
- 1.1 System Configuration 6
- 1.2 Printer Configuration 7
- 1.3 Supplies and Consumables 8
- Option Configuration 9
- 1.4 Specifications 10
- 2. OPERATION DESCRIPTION 12
- 2.1 Main Board (TIG PWB) 13
- 2.3 Power Units 16
- Disconnect 17
- [Maintenance Tools] 18
- Table 2-1 Maintenance Tools 18
- 2.2 Parts layout 19
- For 600dpi 20
- [Printer Unit-1/2] 21
- Figure 2-3 21
- [Printer Unit-2/2] 22
- Figure 2-4 22
- [Cassette Guide Assy (L),(R)] 23
- Figure 2-5 23
- [Duplex Unit] 24
- Figure 2-6 24
- 2.3 Replacing Parts 25
- 2.3.1 Top Cover 27
- (1) Open the Top Cover assy 27
- Figure 2-3-1 Top Cover 27
- 2.3.6 Eject Guide Assy 32
- (1) Remove the cassette 1 34
- 2.3.11 Face-Up Tray 37
- Figure 2-3-11 Face-Up Tray 37
- 2.3.15 Drum Contact Assys 41
- Stage height adjustment jig 43
- Top surface 43
- 2.3.20 Main Cooling Fan 46
- Connectors 47
- 2.3.22 Duplex Guide Assy 48
- Main chassis 52
- 2.3.27 Entrance Sensor PWB 53
- 2.3.30 Exit Sensor Assy 56
- 2.3.42 Fuser Unit 68
- (1) Open the top cover 1 68
- Figure 2-3-42 Fuser Unit 68
- 2.3.44 Duplex Unit 70
- Figure 2-3-44 Duplex Unit 70
- 3. ADJUSTMENT 76
- 3.0 System Maintenance MENU 76
- Maintenance Menu 78
- SWITCH SCAN 80
- MOTOR & CLUTCH TEST 84
- BLACK - ID MOTOR 84
- Figure 3-3 85
- Table 3-2 85
- TEST PATTERN 86
- Pattern 5 Pattern 6 88
- Pattern 7 88
- MTR=*.**KV CTR=*.**KV 89
- P=*** T=*** U=***[###] 89
- H=***% L=***[###] 89
- KTR=*.**KV YTR=*.**KV 89
- NV-RAM INITIAL 90
- TOTAL SHEETS FEED 91
- BLACK IMPRESSIONS 91
- YELLOW IMPRESSIONS 91
- MAGENTA IMPRESSIONS 91
- CYAN IMPRESSIONS 91
- 3.1.2.9 Panel display details 92
- Panel display 92
- Details of jam error display 96
- Value Check 101
- Measurement point 104
- 2-Character correction value 108
- Code content Barcode 108
- 5. TROUBLESHOOTING PROCEDURES 111
- 5.5 Troubleshooting Procedure 112
- Back-up roller thermister 128
- Heat roller thermister 128
- DIAGNOSTIC MODE 139
- XX.XX.XX 139
- Charge Roller 144
- Developing Roller 144
- Toner Supply Roller 144
- 5.6 Fuse check 145
- 6. CONNECTION DIAGRAM 146
- 6.1 Resistance Checks 146
- Feeder Motor 148
- Duplex Motor 148
- 6.2 Program/Font ROM Layouts 150
- (2) Main Controller PWB 152
- (6) N71 PWB 154
- Item Description 156
- INPUT. PRIME 157
- ACKNOWLEDGE 157
- 1. Parts Replacement 160
- APPENDIX C ERROR MESSAGES 165
- 1. Error messages 165
- 5. Other Warnings 177
- PARTS GUIDE 179
- (1) Main Assembly 1/3 181
- (1) Main Assembly 2/3 182
- (1) Main Assembly 3/3 183
- (2) Top Cover Assembly 185
- (2) Top Cover Assembly 186
- (3) Printer Unit Chassis 1/2 187
- (3) Printer Unit Chassis 2/2 188
- (3) Printer Unit Chassis 189
- (4) Paper Tray Guide 191
- (4)Paper Tray Guide 192
- (5)Duplex Unit 193
- (5) Duplex Unit 194
- ALL RIGHTS RESERVED 196
Related products and manuals for Copiers Sharp AR-C240P
Copiers Sharp AR-M208 Service Manual
(32 pages)
(32 pages)
Copiers Sharp AR-C172M User Manual
(2 pages)
(2 pages)
Copiers Sharp AR-M162 User Manual
(4 pages)
(4 pages)
Copiers Sharp SF-1116 Service Manual
(125 pages)
(125 pages)
Copiers Sharp MX-M1100 User Manual
(2 pages)
(2 pages)
Copiers Sharp MX-B401 Specifications
(144 pages)
(144 pages)
Copiers Sharp AR-286 User Manual
(10 pages)
(10 pages)
Copiers Sharp AR-4551 Specifications
(286 pages)
(286 pages)
Copiers Sharp AR-162S User Manual
(16 pages)
(16 pages)
Copiers Sharp AR-5316 Service Manual
(14 pages)
(14 pages)
Copiers Sharp AL-1642CS Specifications
(97 pages)
(97 pages)
Copiers Sharp AL-1000 Series Specifications
(47 pages)
(47 pages)
Copiers Sharp AR-M230 Series Setup Guide
(20 pages)
(20 pages)
Copiers Sharp SF-2216 User Manual
(2 pages)
(2 pages)
Copiers Sharp AR-5320 User Manual
(4 pages)
(4 pages)
Copiers Sharp SF-7320 User Manual
(2 pages)
(2 pages)
Copiers Sharp M450U Specifications
(200 pages)
(200 pages)
© 2020, manymanuals.com. All rights reserved. | 1.852 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals