Sharp AR-C240P Specifications download pdf (Page 116)

116 /

Table 5-1-1 Operator Alarm (4/6)

Message Cause Error Description Solutions

Service Call

160: Y Toner

161: M Toner

162: C Toner

163: K Toner

Service Call

170: Error

171: Error

174: Error

175: Error

Service Call

172: Error

176: Error

Service Call

173: Error

177: Error

Service Call

179: Error

Service Call

180: Error

~

186: Error

Service Call

187: Error

Close cover

310: Top

cover open

Reset fuser

320: Fuser

error

Turn power

OFF and wait

321: MOTOR

OVERHEAT

Open/close

cover

323: Paper

thickness

error

Open/close

cover

324: Paper

thickness

error

Open/close

cover

325: Paper

thickness

error

Open/close

cover

326: Paper

thickness

error

Error detected by toner

sensor.

Short circuit in fuser

thermistor or open

detected (high temp.

or low temp.)

Thermistor indicates

high-temperature error.

Thermistor indicates

low-temperature error.

Wrong fuser standard.

Communication

disability with option

unit detected by engine.

Communication with

control panel disabled.

Printer engine cover

open.

Same unit not detected

upon power ON or

opening cover.

Printer cannot be used

temporarily due to

motor overheat.

Sensor output out of

range with no media.

(Only for Factory Mode)

Sensor output gap out

of range with no media.

(Only for Factory Mode)

Media detect value out

of range.

U-Heavy mode media

detect value out of

range.

1) Is error message displayed?

2) Does error reoccur?

1) Is error message displayed?

2) Does error reoccur?

1) Is error message displayed?

2) Does error reoccur?

1) Is error message displayed?

2) Does error reoccur?

1) Does fuser match with model and power

voltage?

2)

Error reoccurs after setting fuser properly.

1) Is error message displayed?

2) Does error reoccur?

Is cable properly connected to control panel?

1) Check if top cover is open.

2) Check if cover switch is proper.

1) Is error message displayed?

2) Is fuser unit set properly?

3) Does error reoccur?

1) Are foreign objects mixed in sensor?

2) Does printer recover when detecting

paper thickness by opening/closing tray?

3) Does printer recover by power OFF/ON.

1) Are foreign objects mixed in sensor?

2) Does printer recover when detecting

paper thickness by opening/closing tray?

3) Does printer recover by power OFF/ON.

1) Is different media type mixed in?

2) Is media being double fed?

Is different media type mixed in?

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

No

Yes

Yes

Yes

Yes

No

Yes

Yes

Yes

No

Yes

No

Yes

Yes

No

Yes

No

Yes

Yes

Replace toner sensor or assembly

(Y71-PWB).

Same as above.

Turn ON power again.

Replace thermistor and turn power

OFF. Leave aside for 30 min.

Turn ON power again.

Replace thermistor and turn power

OFF. Leave aside for 30 min.

Turn ON power again.

Replace thermistor and turn power

OFF. Leave aside for 30 min.

Set proper fuser.

Check if fuser is set properly.

Replace fuser.

Turn ON power again.

Replace option unit.

Connect properly.

Replace control panel and cable.

Close top cover.

Close side cover.

Replace cover switch.

Check if fuser is set properly.

Reset fuser and turn ON power again.

Replace fuser unit assembly.

Turn ON power after a while.

Remove foreign objects.

Normal.

Remove foreign objects.

Normal.

Remove foreign objects.

Remove foreign objects.

1 2 ... 111 112 113 114 115 116 117 118 119 120 121 ... 195 196

Comments to this Manuals

No comments