Sharp AR-BC260 Specifications download pdf (Page 177)

GENERAL PROGRAMS

Device control

Use these programs when a peripheral device on the

machine has failed or when you wish to temporarily

disable a device. The programs can also be used to

change the function setting of a device as required by

your conditions of use.

"Device control" consists of the following programs:

●Original size detector setting

●Disabling of document feeder

●Disabling of duplex

●Disabling of inverter

●Disabling of stapler

●Disabling of optional paper drawer

●Disabling of large capacity cassette

●Disabling of shifter

●Disabling of finisher

●Saddle stitch position adjust

●Stream feeding mode

●Auto paper selection setting

●Registration adjustment

●Return from copy mode timing

Original size detector setting

This program is used to select the standard original

sizes that can be detected by the original size detection

function. Select one of the four groups indicated below.

The factory default setting is "INCH-1 (AB-1)". Original

size detection by the document glass can also be

disabled (CANCEL DETECTION AT DOCUMENT

GLASS).

* When the reversing single pass feeder is used, these

sizes are only supported for one-sided originals.

If "CANCEL DETECTION AT DOCUMENT GLASS" is

set, originals will be regarded as EXTRA for all copier

functions and no original size will be displayed.

Disabling of document feeder

This program is used to prevent use of the reversing

single pass feeder when it malfunctions. In this case,

scanning can still be performed using the document

glass.

Disabling of duplex

This program is used to disable duplex printing when

the duplex module malfunctions. If this program is set,

only one-sided printing can be performed.

Disabling of inverter

Use this program when you need to prohibit the

inverter function or when the duplex bypass/inverter

unit has failed. When the program is turned on, pages

are only output face-down to the center tray of the

machine. Duplex printing is also not possible (only one-

sided printing is possible).

Disabling of stapler

This program is used to disable stapling when the

stapler unit of the saddle stitch finisher malfunctions.

Disabling of optional paper drawer

This program is used to disable use of the stand/1 x

500 sheet paper drawer, stand/3 x 500 sheet paper

drawer or duplex module/2 x 500 sheet paper drawer

when it malfunctions.

Disabling of large capacity cassette

Use this program when you wish to prohibit use of the

large capacity cassette or when it has failed.

Disabling of shifter

Use this program when you need to prohibit the shifter

function in the center tray or when the shifter has failed.

When the program is turned on, the offset feature that

offsets sets of copies or printed pages in the center tray

will not function.

Disabling of finisher

This program is used to disable use of the saddle stitch

finisher when it malfunctions.

Group

Detectable original sizes

Document feeder tray (for reversing

single pass feeding) or document glass

INCH - 1

11" x 17", 8-1/2" x 14", 8-1/2" x 11",

8-1/2" x 11"R, 5-1/2" x 8-1/2"*

INCH - 2

11" x 17", 8-1/2" x 13", 8-1/2" x 11",

8-1/2" x 11"R, 5-1/2" x 8-1/2"*

3 AB - 1 A3, A4, A4R, A5, B4, B5, B5R

4 AB - 2 A3, A4, A4R, A5, B5, B5R, 8-1/2" x 13"

NOTE

If the duplex module/2 x 500 sheet paper drawer is

disabled, automatic two-sided printing cannot be

performed.

ApollonII_keyope_sec.fm 11 ページ２００４年９月１４日　火曜日　午後１時１６分

1 ... 176 177 178 179 180 181 182 183 184

Comments to this Manuals

No comments

Sharp AR-BC260 Specifications Page 177

Comments to this Manuals

Related products and manuals for Copiers Sharp AR-BC260