Application Note 1LCD Module Application NoteLS013B4DN04INTRODUCTIONThis Application Note provides additional designassistance for Sharp’s LS013B4DN04
LCD Modules LS013B4DN0410 Application NotePROGRAMMINGFor software commands, see the Application Note,Programming Sharp’s Memory LCDs, by Ken Green.In
LS013B4DN04 LCD ModulesApplication Note 11Table 4. Column (X direction) AddressingLINE ADDRESSCOLUMN ADDRESSCA0 CA1 CA2 CA3 CA4 CA5 CA6L1HLLLLLLL2LHL
LCD Modules LS013B4DN0412 Application NoteStatic ModeStatic Mode is the module’s lowest-power mode,with data latches and other circuitry powered down.
LS013B4DN04 LCD ModulesApplication Note 13VCOM InversionPeriodic VCOM inversion impresses a periodicpolarity inversion across the panel to keep a late
LCD Modules LS013B4DN0414 Application NoteFigure 16. EXTMODE = L, Software VCOM ToggleFigure 17. EXTMODE = H, Hardware VCOM ToggleM0 M1 M2M0 M1 M2M0
LS013B4DN04 LCD ModulesApplication Note 15DESIGN NOTES1. This device is static sensitive. Handle it only in astatic-safe environment. 2. Do not press
LCD Modules LS013B4DN0416 Application NoteHANDLING, STORAGE, AND PACKAGING1. This module is not made to be disassembled.Doing so may cause permanent d
LS013B4DN04 LCD ModulesApplication Note 17Packaging DiagramsStack no more than 12 cartons high. Product ispacked in lots of 800. Figure 22. Packagin
LCD Modules LS013B4DN0418 Application NoteRELIABILITYEnvironmental ReliabilityNOTES:1. Ta = ambient temperature, Tp = panel temperature2. Check for an
LS013B4DN04 LCD Modules©2011 by SHARP Corporation Reference Code SMA11008SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.Suggested applications (i
LCD Modules LS013B4DN042 Application NoteMECHANICAL SPECIFICATIONSExternal DimensionsPARAMETER SPECIFICATION UNITScreen Size 1.3InchViewing Area 24.19
LS013B4DN04 LCD ModulesApplication Note 3Connector Specifications NOTES:1. EXTCOMIN is HIGH enabled. When LOW, the serial input flag is enabled. See F
LCD Modules LS013B4DN044 Application NoteAbsolute Maximum Ratings NOTES:1. Applies to EXTMODE.2. Applies to SCLK, SI, SCS, DISP, EXTCOMIN.3. Do not e
LS013B4DN04 LCD ModulesApplication Note 5Figure 3. Setup for Contrast, Reflection Ratio,and ChromaticityFigure 4. Setup for Response TimeLS013B4DN04
LCD Modules LS013B4DN046 Application NoteELECTRICAL SPECIFICATIONSHere are the Recommended Operating Conditionsfor this module, with VSS (GND) = 0V an
LS013B4DN04 LCD ModulesApplication Note 7Figure 7. Power Supply SequencingNormal OperationNote 1Note 2Note 2Note 2Note 2Note 1On SequenceVDD/VDDA (5
LCD Modules LS013B4DN048 Application NoteSIGNAL DESCRIPTIONSInput signal characteristics are given in Table 2 andTable 3; refer to Figure 8 for timing
LS013B4DN04 LCD ModulesApplication Note 9Timing Diagrams Figure 8. SCS, SI, SCLK, EXTCOMIN, and DISP SignalsSCSSCS, SI, SCLK SignalEXTCOMIN SignalDI
Comments to this Manuals