Sharp MD X5 Service Manual download pdf (Page 26)

MD-X5H/CP-X5H

– 26 –

Step 18 Press once the CD PLAY button. TCRS comparison level 1 for high reflection [ T C R S C 1 P _ ]

Step 19 Press once the CD PLAY button. Comparison level in case of COUT generation (playback) [ C O T L V p _ _ ]

Step 20 Press once the CD PLAY button. Comparison level in case of COUT generation (pecord) [ C O T L V r _ _ ]

Step 21 Press once the CD PLAY button. Auto-move waiting time setting [ W A I T m_ _ _ ]

Step No.

Setting Method

Remarks Display

d) Slide setting

Step 1 Testmode STOP state [ t s m e ]

Step 2

Press the CD PLAY button seven times.

EEPROM setting menu [E E P R O M _ S E T]

Step 3 Press once the MD PLAY button. Focus setting menu [ _ _ F o c u s _ _ _ ]

Step 4

Press the CD PLAY button three times.

Slide setting menu [ _ _ _ S l e d _ _ _ ]

Step 5 Press once the MD PLAY button. Slide system loop filter gain constant setting [ S L G _ _ _ _ _ ]

Step 6 Press once the CD PLAY button. Slide system loop filter f characteristic constant 2 setting [ S L 2 _ _ _ _ _ ]

Step 7 Press once the CD PLAY button. Slide output limitter setting [ S L D L I M _ _ ]

Step 8 Press once the CD PLAY button. Slide servo output dead zone level setting [ S L D L E V _ _ ]

Step 9 Press once the CD PLAY button. Slide kick pulse level setting (forced move) [ S L K L V k _ _ ]

Step 10 Press once the CD PLAY button. Slide kick pulse level setting (for 10 lines jump auxiliary use) [ S L K L V t _ _ ]

Step 11 Press once the CD PLAY button. Slide kick pulse level setting (move) [ S L K L V m _ _ ]

Step No.

Setting Method

Remarks Display

• : Setting volue

• Pressing the REC button causes reversing.

• If the VOL UP button is pressed while the specific setting item is indicated, the setting increases, and the new setting is set in LSI.

• If the VOL DOWN button is pressed while the specific setting item is indicated, the setting decreases, and the new setting is set in LSI.

• If the VOL UP/VOL DOWN button is held down, the setting changes continuously with 100 ms cycle.

•

: Setting volue

• Pressing the REC button causes reversing.

• If the VOL UP button is pressed while the specific setting item is indicated, the setting increases, and the new setting is set in LSI.

• If the VOL DOWN button is pressed while the specific setting item is indicated, the setting decreases, and the new setting is set in LSI.

• If the VOL UP/VOL DOWN button is held down, the setting changes continuously with 100 ms cycle.

Temperature measurement value correction table

Ambient temperature

correction

12.2 °C ~ 15.8 °C -0 3 H

15.9 °C ~ 19.6 °C -0 2 H

19.7 °C ~ 23.2 °C -0 1 H

23.2 °C ~ 26.8 °C ± 0 H

26.9 °C ~ 30.7 °C +0 1 H

30.8 °C ~ 34.3 °C +0 2 H

34.4 °C ~ 37.9 °C +0 3 H

EEPROM record value = Microcomputer measurement value +

Correction

* EEPROM record value

Value to be measured by the microcomputer at +25°C

* Microcomputer measurement value

Value to be measured by the microcomputer at specific

temperature

* Correction value

Correction value for conversion to measurement value at

+25°C (see the table shown left)

Ambient temperature

temperature code

19.6 °C ~ 30.7 °C0 6

8.7 °C ~ 19.6 °C0 7

• Temperature code check

The temperature code is read after automatic adjustment. If it is within the range shown below, the adjustment is OK.

1 2 ... 21 22 23 24 25 26 27 28 29 30 31 ... 103 104

Comments to this Manuals

No comments

Sharp MD X5 Service Manual Page 26

Comments to this Manuals