Sharp MD X5 Service Manual download pdf (Page 8)

MD-X5H/CP-X5H

– 8 –

Caution on Disassembly

Whe disassembling the machine or assenbling it after

repair, observe the following instructions so as to ensure

safety and keep its performance.

1. Unload the compact disc, and mini-disc from machine.

2. Be sure to unplug the power cable before starting

disasembly of the machine.

3. When disassenbling each section, remove the nylon

band or wire arrangement.

If a screw of improper length is fit to the MD mechanism.

(a screw fit the part to the mechanism chassis of MD

section), it may cantact the optical pickup, impeding

normal operation. Hence, due care must be taken.

4. While repairing, pay utmost attention to static electricity

on ICs.

1 Top Cabinet 1. Screw ................ (A1) x4 8-1

2 Side Panel 1. Screw ................ (B1) x10 8-1

(Left/Right)

3 Rear Panel 1. Screw ................ (C1) x6 8-1

2. Socket ............... (C2) x1 8-2

4 Power Amp. PWB 1. Screw ................ (D1) x2 8-2

2. Socket ............... (D2) x4

5 Main PWB 1. Screw ................ (E1) x2 8-2

2. Socket ............... (E2) x4 8-3

3. Flat Wire ............ (E3) x1

6 MD Holder 1. Screw ................ (F1) x4 8-3

(MD Unit) 2. Socket ............... (F2) x1

3. Flat Cable .......... (F3) x1

7 Power Supply PWB 1. Screw ................ (G1) x4 8-3

8 CD Holder 1. Screw ................ (H1) x4 9-1

(CD Mechanism/ 2. Socket ............... (H2) x1

CD Servo PWB) 3. Flat Wire ............ (H3) x1

9 Front Panel 1. Screw ................ (J1) x2 9-1

10 Display PWB 1. Screw ................ (K1) x10 9-1

11 Jack PWB 1. Screw ................ (L1) x2 9-2

12 CD Servo PWB 1. Screw ................ (M1) x3 9-3

(Note 1)

13 CD Mechanism 1. Screw ................ (N1) x3 9-4

14 MD Mecha Unit 1. Screw ................ (P1) x7 9-5

15 MD Main PWB 1. Screw ................ (Q1) x4 9-6

2. Socket ............... (Q2) x6

16 MD Mechanism 1. Screw ................ (R1) x4 10-1

DISASSEMBLY

Figure 8-2

Figure 8-3

STEP REMOVAL PROCEDURE FIGURE

Figure 8-1

MD-X5H

STEP REMOVAL PROCEDURE FIGURE

1 Front Panel 1. Net........................... (A1) x2 10-2~5

3. Screw ...................... (A2) x6

2 Speaker 1. Screw ...................... (B1) x4 10-6

3 Tweeter 1. Screw ...................... (C1) x2 10-6

CP-X5H

MD-X5H

(F1)x2

ø2.6x10mm

(F1)x2

ø2.6x10mm

(G1)x4

ø4x10mm

Power Supply PWB

MD Holder

MD Mecha Unit

(D2)x1

(F2)x1

(F3)x1

Note 1: After disconnecting the optical pickup connector wrap

the front end of connector in the conductive aluminium foil so

as to prevent electrostatic damage of optical pickup.

(A1)x1

ø3x10mm

(A1)x2

ø3x10mm

(A1)x1

ø3x10mm

(B1)x1

ø3x10mm

(B1)x1

ø3x10mm

(B1)x1

ø3x10mm

(B1)x2

ø3x10mm

(B1)x2

ø3x10mm

(B1)x2

ø3x10mm

(C1)x6

ø3x8mm

(B1)x2

ø3x10mm

Top Cabinet

Side Panel

(Left)

Side Panel

(Right)

Rear Panel

Pull

(D1)x1

ø3x10mm

(E1)x1

ø3x10mm

(E1)x1

ø3x10mm

(E2)x1

(D2)x1

(E2)x1

(E3)x1

(D2)x1

(D1)x1

ø3x10mm

Power Amp. PWB

(E2)x2

Main PWB

(C2)x1

1 2 3 4 5 6 7 8 9 10 11 12 13 ... 103 104

Comments to this Manuals

No comments

Sharp MD X5 Service Manual Page 8

Comments to this Manuals