Sharp XG-NV6XM Specifications Page 48
- Page / 65
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
47
Maintenance &
Troubleshooting
Problem
• Blocked air intake.
• Clogged air filter.
• Cooling fan breakdown.
• Internal circuit failure.
• Burnt-out lamp.
• Lamp circuit failure.
• The bottom filter cover is
open.
Lamp/Maintenance Indicators
Maintenance Indicator
The internal
temperature is
abnormally high.
TEMPERATURE
WARNING indicator
LAMP REPLACE-
MENT indicator
POWER indicator
The lamp does not
light up.
The POWER
indicator flashes in
red when the
projector is on.
Condition Possible Solution
• Relocate the projector to an area with
proper ventilation.
• Clean the filter.
(See page 46.)
• Take the projector to your nearest
Authorised Sharp Industrial LCD Products
Dealer or Service Centre for repair.
• Take the projector to your nearest
Authorised Sharp Industrial LCD Products
Dealer or Service Centre for repair.
• Securely install the bottom filter cover.
Maintenance Indicators
• The warning lights on the projector indicate problems
inside the projector.
• There are two warning lights: a TEMPERATURE
WARNING indicator which warns that the projector is
too hot, and a LAMP REPLACEMENT indicator which
lets you know when to change the lamp.
• If a problem occurs, either the TEMPERATURE
WARNING indicator or the LAMP REPLACEMENT
indicator will light up red. After turning off the power,
follow the procedures given below.
TEMPERATURE
WARNING
indicator
LAMP
REPLACEMENT
indicator
POWER
indicator
• If the TEMPERATURE WARNING indicator lights up, follow the above possible solutions and then wait until the projector has
cooled down completely before turning the power back on. (At least 5 minutes.)
• If the power is turned off and then turned on again, as during a brief rest, the LAMP REPLACEMENT indicator may be
triggered, preventing the power from going on. Should this occur, take the power cord out of the wall outlet and put it back
in again.
Lamp
The lamp in this projector operates for approximately 2,000 cumulative hours, depending on the usage environ-
ment. It is recommended that the lamp be replaced after 1,900 cumulative hours of use or when you notice a
significant deterioration of the picture and colour quality. At this point, take the projector to your nearest Authorised
Sharp Iudustrial LCD Products Dealer or Service Centre to have the lamp replaced. The lamp usage time can be
checked with the On-screen Display (see page 39).
CAUTION
• Intense light hazard. Do not attempt to look into the aperture and lens while the projector is operating.
• As the usage environment can vary significantly, the projector lamp may not operate for 2,000 hours.
- LCD PROJECTOR 1
- OPERATION MANUAL ENGLISH 2
- Important Safeguards 3
- Outstanding Features 4
- Contents 5
- Usage Guidelines 6
- Accessing the PDF Manuals 7
- Part Names 8
- Remote Control 9
- Inserting the batteries 9
- Setup & Connections 10
- Setting up the Projector 11
- 2. Connecting the Projector 12
- R), G/G sync (Y), B (PB) 13
- Connecting RS-232C Port 15
- IBM or IBM compatible PC 16
- Macintosh 16
- Operation 17
- Press Power ON 18
- Press POWER OFF 18
- 2. Setting up the Screen 19
- Rotate feet to make minor 20
- Reversed Image Setup 21
- Ceiling-mount Setup 21
- Controlling the Projector 22
- Using the Wireless Mouse 22
- Wired Remote Control 23
- Items on the INPUT1 or 25
- INPUT2 Mode Menu Bar 25
- 10 cm–1 m 26
- Picture Adjustments 28
- Audio Adjustments 29
- Computer Image Adjustments 30
- Auto Sync Adjustment 31
- Auto Sync Display Function 31
- Saving the adjustment setting 32
- Selecting a saved setting 32
- Special Mode Adjustment 33
- Useful Features 34
- Digital Image Magnification 35
- Gamma Correction 36
- Black Screen Function 38
- Selecting the Economy Mode 39
- I/P Conversion 40
- Checking the Lamp Usage Time 40
- Selecting the Signal Type 41
- Checking the Input Signal 41
- Setting a Background Image 42
- Selecting a Startup Image 42
- Reverse/Invert Image Function 43
- Using the Presentation Tools 44
- Status Function 45
- Maintenance & 46
- Troubleshooting 46
- Air Filter Maintenance 47
- Lamp/Maintenance Indicators 48
- Using the Kensington Lock 49
- Appendix 50
- Connection Pin Assignments 51
- RS-232C Port Specifications 52
- For IBM and compatibles 55
- For Macintosh Series 55
- Specifications 57
- Dimensions 58
- Sans-serif 60
- Good Bad Good 61
- Glossary 63
- SHARP CORPORATION 65
Related products and manuals for Projectors Sharp XG-NV6XM
Projectors Sharp CE-LK1P Specifications
(28 pages)
(28 pages)
Projectors Sharp AN-WC11B Specifications
(131 pages)
(131 pages)
Projectors Sharp PGC30XU Service Manual
(108 pages)
(108 pages)
Projectors Sharp XG-NV5XB User Manual
(54 pages)
(54 pages)
Projectors Sharp XV-Z1A Service Manual
(65 pages)
(65 pages)
Projectors Sharp AN-SV100T User Manual
(2 pages)
(2 pages)
Projectors Sharp AN-LV140X User Manual
(26 pages)
(26 pages)
Projectors Sharp PG-M20XU Service Manual
(97 pages)
(97 pages)
Projectors Sharp XG-C40XUSL User Manual
(33 pages)
(33 pages)
Projectors Sharp XG-C60X User Manual
(19 pages)
(19 pages)
Projectors Sharp XG-XV1E Service Manual
(44 pages)
(44 pages)
Projectors Sharp XV-Z200E Service Manual
(140 pages)
(140 pages)
Projectors Sharp PG-A20X Service Manual
(124 pages)
(124 pages)
Projectors Sharp XG-P20XD Service Manual
(137 pages)
(137 pages)
Projectors Sharp AN-NV6T User Manual
(2 pages)
(2 pages)
Projectors Sharp CE-LK1P Specifications
(27 pages)
(27 pages)
Projectors Sharp XV-Z20000 User Manual
(2 pages)
(2 pages)
© 2020, manymanuals.com. All rights reserved. | 1.448 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals