Sharp MX-CFX1 Service Manual

SERVICE MANUALParts marked with " " are important for maintaining the safety of the set. Be sure to replace these parts withspecified ones f

MX-CFX1 OPERATIONAL DESCRIPTION 5 – 416) The reverse sensor is turned OFF. The trailing edge of thesheet is detected, and the flapper solenoid in t

MX-CFX1 OPERATIONAL DESCRIPTION 5 – 5Setting procedure:1) Place a sheet in the tray.2) Press the STAPLE MODE switch on the operator panel.3) Each ti

MX-CFX1 OPERATIONAL DESCRIPTION 5 – 65. LED indication on operator panelNOTE: For LED status, each blank means "not lit."Status Cause Expl

MX-CFX1 OPERATIONAL DESCRIPTION 5 – 76. Paper jam/error detectionA. List of Paper jamsB. Error detection(1) EEPROM errorsExplanation:1) Timeout erro

MX-CFX1 DISASSEMBLY AND ASSEMBLY 6 – 1MX-CFX1Service Manual [6] DISASSEMBLY AND ASSEMBLY1. Paper feed separation unitA. Pickup roller & paper fe

MX-CFX1 DISASSEMBLY AND ASSEMBLY 6 – 22. Paper feed unitA. Horizontal pass roller 1 and registration rollerParagraph in Sub Section.1) Open the top

MX-CFX1 DISASSEMBLY AND ASSEMBLY 6 – 34) Remove the cover A.5) Remove the tray unit.6) Remove the cover A.A: Horizontal pass roller 2B: Timing rolle

MX-CFX1 DISASSEMBLY AND ASSEMBLY 6 – 4D. Paper guide3. Drive unitA. Belts1) Open the top cover.2) Remove the rear cover.B. Gears1) Open the top cove

MX-CFX1 DISASSEMBLY AND ASSEMBLY 6 – 5B. Transport motor1) Remove the rear cover.2) Remove the transport motor.C. Reverse motor1) Remove the front c

MX-CFX1 DISASSEMBLY AND ASSEMBLY 6 – 6C. Registration sensor and empty sensor1) Open the top cover.2) Remove the front cover and rear cover.3) Detac

CONTENTS[1] PRODUCT OUTLINE. . . . . . . . . . . . . . . . . . . . . . . . 1-1[2] SPECIFICATIONS1. Basic specifications . . . . . . . . . . . . . .

MX-CFX1 DISASSEMBLY AND ASSEMBLY 6 – 77. Note on assemblyA. Reverse flapper solenoid adjustment1) Rotate the solenoid lever (LVR-FM-SOL) fully clock

MX-CFX1 MAINTENANCE 7 – 1MX-CFX1Service Manual [7] MAINTENANCE1. Maintenance listNote 1 : Replacement reference: For replacement, refer to each pape

MX-CFX1 ADJUSTMENTS 8 – 1MX-CFX1Service Manual [8] ADJUSTMENTS1. Paper width detection level setting (adjustment)1) Enter the diag mode.Press and ho

MX-CFX1 SIMULATION 9 – 1MX-CFX1Service Manual [9] SIMULATION1. List2. Details of trouble code 3 3-30PurposeOperation test/CheckFunction (Purpose)Use

MX-CFX1 SIMULATION 9 – 2 3-32PurposeSetting (Adjustment)Function (Purpose)Used to set the adjustment value of theinserter paper width detection leve

MX-CFX1 SELF DIAG MESSAGE AND TROUBLE CODE 10 – 1MX-CFX1Service Manual [10] SELF DIAG MESSAGE AND TROUBLE CODEProblem The inserter does not perform

MX-CFX1 SELF DIAG MESSAGE AND TROUBLE CODE 10 – 2Problem The machine does not detect the paper.Case1 Cause JAM cover open/close switch fault Check a

MX-CFX1 SELF DIAG MESSAGE AND TROUBLE CODE 10 – 3M E M O

MX-CFX1 ELECTRICAL SECTION 11 – 1MX-CFX1Service Manual [11] ELECTRICAL SECTION1. Actual wiring chartReverse sensorPaper exit sensorReverse unit open

MX-CFX1 ELECTRICAL SECTION 11 – 2HousingContactHousingContactHousingContactContactHousingContactContactSleeveFASTON TerminalHousingContactHousingCon

MX-CFX1 PRODUCT OUTLINE 1 – 1MX-CFX1Service Manual [1] PRODUCT OUTLINEThis inserter is an optional unit for the MX-5500N/MX-6200N/MX-7000N series of

MX-CFX1 ELECTRICAL SECTION 11 – 32. Circuit descriptionA. OutlineThis circuit controls paper feed, transport, reverse, and delivery.This circuit con

MX-CFX1 ELECTRICAL SECTION 11 – 4B. Circuit Detail(1) Communication Circuit1) TxD signal2) RxD signalThis circuit communicates with the main unit an

MX-CFX1 ELECTRICAL SECTION 11 – 5R39 is a current limiting resistor for the LED. R34 is a load resistorfor the sensor.3) Reverse Unit Open/Closed Se

MX-CFX1 ELECTRICAL SECTION 11 – 69) Tray Sensor (T_SEN)T_SEN uses the photointerrupter integrated with an LED and aphototransistor.The sensor detect

MX-CFX1 ELECTRICAL SECTION 11 – 73) Transport Motor Drive Circuit (Y_MOT)This circuit rotates/stops Y_MOT and controls its rotational direc-tion and

MX-CFX1 ELECTRICAL SECTION 11 – 8IC4-Pin1 (CS) is the chip selection terminal, and stays "H" duringpassing data.IC4-Pin2 (SK) is the seria

MX-CFX1 ELECTRICAL SECTION 11 – 99) Operator Panel CircuitThis is the circuit of the operator panel board.The operator panel drive board turns each

No part of this publication may be reproduced,stored in a retrieval system, or transmitted inany form or by any means, electronic, mechanical,photoco

* Applicable to battery-operated equipment* Applicable to battery-operated equipment

SHARP CORPORATIONDigital Document System GroupCS Promotion CenterYamatokoriyama, Nara 639-1186, Japan2006 June Printed in Japan

MX-CFX1 SPECIFICATIONS 2 – 1MX-CFX1Service Manual [2] SPECIFICATIONS1. Basic specificationsName InserterType Floor standingTransport reference Cente

MX-CFX1 EXTERNAL VIEWS AND INTERNAL STRUCTURES 4 – 1MX-CFX1Service Manual [4] EXTERNAL VIEWS AND INTERNAL STRUCTURES1. External components2. Sensors

MX-CFX1 EXTERNAL VIEWS AND INTERNAL STRUCTURES 4 – 23. Motors, solenoid, and clutch2 H_SEN Reverse sensor Reflective sensorDetects that a sheet to b

MX-CFX1 OPERATIONAL DESCRIPTION 5 – 1MX-CFX1Service Manual [5] OPERATIONAL DESCRIPTION1. StructureA. Cross-sectional view (Main body)B. Drive system

MX-CFX1 OPERATIONAL DESCRIPTION 5 – 2B. Normal paper feed operation of inserter (online/offline)[Paper loading]1) A sheet is placed in the paper fee

MX-CFX1 OPERATIONAL DESCRIPTION 5 – 3C. Reverse paper feeding operation of inserter[Paper loading]1) A sheet is placed in the paper feed tray of the