Sharp R-310J Operator's Manual

R-310 Round Product Labeler Operator’s Manual Serial #

Page 10 WASTE REMOVAL Break the web as shown and turn it opposite the running direction to loosen it. Then remove the retaining clip and remove th

Page 11 CARRIAGE ADJUSTMENT AND PRODUCT PLACEMENT SET CARRIAGE AS FOLLOWS 1. The product centerline should be slightly behind drive roller center

Page 12 HORIZONTAL CARRIAGE ADJUSTMENT Using adjusting screws (D, Fig. 6), you may slide “Standard Carriage Assembly” left or right to improve or c

Page 13 VERTICAL CARRIAGE ADJUSTMENT This adjustment provides a means to relocate the lower carriage roller assembly into one of several pair of ho

Page 14 CARRIAGE ADJUSTMENT FOR TAPERED PRODUCTS A tapered product can be labeled on the R-310 by adjusting the carriage as follows. 1. Remove

Page 15 4. Place a product on the rollers and move the product and roller assembly so the product contacts the drive roll evenly. 5. Position the

Page 16 PEELER PLATE ADJUSTMENT The peeler plate assembly may require adjustment with the change of label length or product diameter. A short label

Page 17 ADJUST PEELER PLATE AS FOLLOWS 1. Using the provided 9/64” Allen wrench just loosen – DO NOT REMOVE - the two 8-32 SHCS located on the lef

Page 18 SECTION 3 OPERATION Select the product to be labeled and place it on the white carriage rollers. Move the product to the right against t

Page 19 AIR ASSEMBLY ADJUSTMENTS Turn you attention to the underneath of the R-310. These two valves on the air regulator control the speed at wh

Page 2 Operator’s Manual Version: E 1/28/2002 The information in this manual is subject to change without notice. No part of this manual may b

Page 20 AIR REGULATOR Turn your attention to the side where the air regulator is mounted. The Air Regulator is used to raise or lower the air press

Page 21 Hold Index finger on top of star to keep it steady. Fig 17 SECTION 4 MAINTENANCE STARWHEEL After continued use, the starwheel label sens

Page 22 GENERAL MAINTENANCE Drive rolls: The drive rolls must be kept clean. Wash with lacquer thinner or other recommended solvents to remove gum

Page 23 TECHNICAL SUPPORT When calling for Technical Support: have your Model # : R310 and the Serial Number ready (located on main base plate on

Page 24 DRAWINGS AND BILL OF MATERIALS POWER MODULE See Drawing L15-D-02 WEBBING DIAGRAM See Drawing 310-W-00 MAIN ASSEMBLY See Drawing 310-I-00E FR

F:\LABELERS\R-310\Manual\Recommended Spare parts List.doc Printed 5/11/98 R-310 ROUND PRODUCT LABELER RECOMMENDED SPARE PARTS Part Number Description

Bill of MaterialITEM NUM: PART NUMBER: PART DESCRIPTION: QTY:MAIN ASSEMBLYR31001 SRL-500-42 BRACKET, OUTER BEARING 102 L-144-M BLOCK, 3/8" BEARIN

Bill of MaterialITEM NUM: PART NUMBER: PART DESCRIPTION: QTY:MAIN ASSEMBLYR31060 700025 GUIDE, 1/2" SPLIT NYLON WEB>> 261 MD-717 COVER, STA

Page 3 Table of Contents SECTION 1 OVERVIEW...4 INTRODUCTION...

Bill of MaterialITEM NUM: PART NUMBER: PART DESCRIPTION: QTY:AIR CYLINDER MOUNTING ASSEMBLYR31001 100099 VALVE, 120VAC 3WY MAC AIR 102 100108 FTNG, MI

Bill of MaterialITEM NUM: PART NUMBER: PART DESCRIPTION: QTY:FRONT PANEL ASSEMBLYR31001 200198 MODULE, POWER 102 850015 SCREW, 6-32 X 1-1/4" L SH

Bill of MaterialITEM NUM: PART NUMBER: PART DESCRIPTION: QTY:REGULATOR ASSEMBLYR31001 100300 REGULATOR, AIR 102 100209 FTNG, 1/8 90 STREET ELL 103 100

Bill of MaterialITEM NUM: PART NUMBER: PART DESCRIPTION: QTY:REGULATOR ASSEMBLY W/CODERR31001 100300 REGULATOR, AIR 102 100209 FTNG, 1/8 90 STREET ELL

Page 4 SECTION 1 OVERVIEW INTRODUCTION Thank you for purchasing the R-310 semi-automatic round product labeler. The R-310 is known for high qu

Bill of MaterialITEM NUM: PART NUMBER: PART DESCRIPTION: QTY:STANDARD CARRIAGE ASSEMBLYR31001 SRL-500-62AASS'Y, IDLER ROLLER 202 SC-006 COLLAR, S

Bill of MaterialITEM NUM: PART NUMBER: PART DESCRIPTION: QTY:R. H. 13" UNWIND ASSEMBLYR31001 UND-001 BAR, LABEL REEL MOUNTING 102 UND-002 SHAFT,

Page 5 UN-PACKING INSTRUCTIONS When the machine is received, the shipping carton will contain the following items. 1. R-310 Body. 2. Foot Switch.

Page 6 PRODUCT WARRANTY Universal Labeling Systems, Inc. warranties all parts to be free from defects in material and workmanship for a period of o

Page 7 SPECIFICATIONS Electrical Power: 120VAC +/- 10%, 3 Amps, 60Hz Compressed Air: Clean, Dry, 20-40PSI, 5CFM Product size: ½” to 6” (

Page 8 SECTION 2 SETUP ASSEMBLING THE R310 The only item that needs to be added to the R-310 is the Unwind Assy. 1. Turn your attention to the

Page 9 WEBBING THE R-310 Place the roll of labels on the unwind spool. Install the label disc and while pressing it against the label reel, tighten