Sharp SF-2414 Service Manual Page 75
- Page / 131
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Repeat procedures 1) to 8) until the horizontal copy magnifica-
tion ratio in the normal (100%) copy mode is within the specified
range. (SPF copy mode: Horizontal copy magnification ratio ad-
justment)
1) Set the copied scale image paper which was made in the
horizontal copy magnification ratio adjustment in the docu-
ment table copy mode so that the scale image is horizontal in
the SPF.
Note that the copy magnification ratio of the copied scale
image must be proper.
2) Set the copy magnification ratio to 100%.
3) Make a copy on A4 or 8 1/2" x 11" paper.
4) Measure the length of the copied scale image.
5) Calculate the horizontal copy magnification ratio.
Horizontal copy magnification ratio =
Copy image size
Original size
x 100 (%)
6) Check that the actual copy magnification ratio is within the
specified range (100 ±0.8%).
If it is out of the specified range, perform the following proce-
dures.
7) Execute simulations 48-3. (C → 0 → 0 → C → 48 → CB → 3
→ CB)
The set horizontal copy magnification ratio in the SPF copy
mode will be displayed in the COPIES SELECTED display.
8) Enter a new horizontal copy magnification ratio with the
numeric key and press PRINT button. The above procedure
changes the document feed speed of the SPF and the
horizontal copy magnification ratio.
When the copy magnification ratio is set to a larger value, the
actual copy magnification ratio becomes larger.
When the copy magnification ratio is set to a smaller value,
the actual copy magnification ratio becomes smaller.
Repeat procedures 1) to 8) until the horizontal copy mag-
nification ratio in the SPF copy mode is within the specified
range.
VII. Troubles caused by improper adjustment
(7) Uniformity adjustment
I. Summary
The uniformity adjustment is performed by changing the ex-
posure plate position attached to No.1 scanner unit.
The above procedure changes the balance of light quantity
radiated onto the document.
II. Purpose
The purpose of this adjustment is to have uniform copy density.
III. Note
When this adjustment is performed, the exposure will be
changed. Therefore, the copy density adjustment must be per-
formed after this adjustment. Also, this adjustment must be per-
formed always before the copy density adjustment.
IV. Cases when the adjustment is required
1) When the reflector is replaced.
2) When the copy lamp is replaced.
3) When the exposure adjustment plate is disassembled or
replaced.
4) In maintenance
V. Necessary tools
*
Screwdriver (+)
*
A4 or 8 1/2" x 11" paper
*
Half-tone paper of A4 or 8 1/2" x 11" or larger
100 110 120
130
150
140
mm
1/2mm
JAPAN
HARDDENCD
STAINLESS
Shizuoka
100 110 120
130
150
140
mm
1/2mm
JAPAN
HARDDENCD
STAINLESS
Shizuoka
110
10 20
10 20
Original scale
Paper feed
direction
Reference Comparison point Copy
7 – 18
- SERVICE MANUAL 1
- MODEL SF-2314 1
- MODEL SF-2414 1
- MODEL SF-2514 1
- CONTENTS 2
- [1] GENERAL DESCRIPTION 4
- [2] PRODUCT SPECIFICATIONS 5
- 3. Supplies 7
- Storage period: 8
- Upper unit 9
- Lower unit 9
- 6 7 8 14 15 16 17 18 10
- 11 12 13 14 15 16 17 18 19 20 11
- 1. Packing drawing (SF-2514) 16
- 2. Installation 16
- (2) Space around the machine 17
- (3) Installing table 17
- Mirror unit fixing screw 18
- (3) Developer setting 19
- Developer unit 20
- Fixing screw 20
- (step screw) 20
- Mounting screw A 22
- Mounting screw B 22
- Mounting 23
- Multi bypass feeder unit 24
- [5] GENERAL DESCRIPTIONS OF 25
- EACH SECTION 25
- 3. Fuser, paper exit section 26
- 4. Developer section 26
- 5. Optical system 27
- 5-2. Basic operations 28
- 6. Copy process 30
- (3) Actual process 31
- Step 3 (Main Charging) 32
- Step 4 (Exposure) 32
- Step 5 (Development) 33
- Step 6 (Transfer) 34
- Step 7 (Separation) 34
- Step 8 (Cleaning) 35
- Step 9 (Discharging) 35
- (5) Process correction system 36
- 2) Correction operation 36
- [Initial setting] 37
- [Correction timing] 37
- [Correction operation] 37
- 7. SPF section (SF-2514 only) 38
- (Timing chart) 38
- [6] DISASSEMBLY AND ASSEMBLY 39
- 1-3. Separation roller 40
- One-way clutch side 41
- 1-6. Transport belt 42
- 1-7. Socket holder unit 42
- 1-8. Lower unit PWB 42
- 1-10. Power unit 42
- 2. Manual paper feed section 43
- 3. Fuser section 44
- 3-6. Scraper replacement 46
- 4. Optical system 47
- 4-6. Optical unit removal 49
- 5. SPF section 51
- 1, 2." 52
- 5-5. Clutch/solenoid removal 53
- 5-6. Sensor removal 53
- 6. Drum section 54
- 7. Developer section 54
- 7-3. Toner motor removal 55
- 7-4. Toner density sensor 55
- 9-3. Ventilation fan motor 56
- 9-1. Ozone filter 56
- 9-4. Transport roller clutch 57
- 9-5. Paper exit sensor 57
- [7] ADJUSTMENTS 58
- 0.625±0.03mm 59
- 2. Optical section 60
- Document Copy 63
- Document Copy A Copy B 64
- Cam fixing screw 65
- Do not move 65
- No.2 scanner unit 67
- Positioning plate 67
- Scanner unit drive pulley 67
- Document Copy C Copy D 68
- Change the right side 69
- Change the left side 69
- Copy paper 70
- Optical unit cover 71
- Copy image size 73
- Original size 73
- (7) Uniformity adjustment 75
- Paper exit 76
- Half-tone copy 76
- Less exposure 76
- (Dark copy) 76
- Scale image lead edge 78
- Enlargement copy (x 1.54) 78
- Reduction copy (x 0.64) 79
- Copy scale image 80
- Paper lead edge 80
- current void area (mm) 81
- 3. COPY DENSITY ADJUSTMENT 83
- Not copied 84
- Slightly copied 84
- adjustment 85
- Charger wire 87
- Improper 87
- [8] SIMULATIONS 88
- 4. Purpose list 89
- 5. Details of simulations 90
- ÷ Document length x 100 [%] 94
- EXP1~5 voltage 98
- Full power 98
- 6. User simulation 100
- Auto start function 101
- (2) User simulation prcedure 101
- (3) User program code table 102
- [9] SELF DIAG 103
- 4. Self diag contents 104
- 1) Paper feed section 109
- 2) Transport section 109
- [10] SERVICING AT MEMORY 110
- TROUBLE AND MAIN 110
- CONTROL PWB REPLACEMENT 110
- 4. Set value recording sheet 113
- 5. Memory simulation list 114
- [11] MAINTENANCE 115
- [12] ELECTRICAL SECTION 116
- M37702M2-XXXFP 117
- 3 Block diagram 118
- IN XIN IN Clock IN 119
- OUT XOUT OUT Clock OUT 119
- H=+32V, VB=+24V 120
- 1 General 121
- Stepping motor time chart 122
- External view 5P5 123
- Delay capacity 123
- V3' 124
- (1) Outline 126
- (2) Display circuit 127
- 1 Block diagram 127
- 2 Operation 127
- (3) LED display 128
- • AC PWB unit 128
- • In the main PWB unit 129
- COPYRIGHT 131
- 1997 BY SHARP CORPORATION 131
Related products and manuals for Copiers Sharp SF-2414
Copiers Sharp Multi Access User Manual
(12 pages)
(12 pages)
Copiers Sharp AL-2020 User Manual
(32 pages)
(32 pages)
Copiers Sharp MX-M503 User Manual
(12 pages)
(12 pages)
Copiers Sharp AR-CF2 User Manual
(12 pages)
(12 pages)
Copiers Sharp AR-M160 Specifications
(33 pages)
(33 pages)
Copiers Sharp FO-DC550 Specifications
(116 pages)
(116 pages)
Copiers Sharp AR-D25 User Manual
(6 pages)
(6 pages)
Copiers Sharp MX-C310 User Manual
(12 pages)
(12 pages)
Copiers Sharp FO-2080 Specifications
(41 pages)
(41 pages)
Copiers Sharp AL-1631 Specifications
(100 pages)
(100 pages)
Copiers Sharp AR-235 Operations Instructions
(130 pages)
(130 pages)
Copiers Sharp AL-1555 Series Specifications
(89 pages)
(89 pages)
Copiers Sharp FO-155 Specifications
(187 pages)
(187 pages)
Copiers Sharp Multi Access User Manual
(12 pages)
(12 pages)
Copiers Sharp AL-1551CS Specifications
(54 pages)
(54 pages)
Copiers Sharp AR-C170M User Manual
(28 pages)
(28 pages)
Copiers Sharp AR-FX4 Service Manual
(98 pages)
(98 pages)
Copiers Sharp AR-FX7 Service Manual
(110 pages)
(110 pages)
© 2020, manymanuals.com. All rights reserved. | 0.401 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals