Sharp SF-2414 Service Manual Page 68
- Page / 131
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
10) Check the horizontal image distortion.
If LL = LR, there is no horizontal distortion.
LL and LR = Distance between the copy
horizontal line and the outer edge
of the black background
11) If LL is not equal to LR, perform the following procedure.
Loosen the setscrew of the scanner unit drive pulley in the
front or the rear frame.
12) Without moving the scanner unit drive pulley shaft, manual-
ly turn the scanner unit drive pulley whose setscrew was
loosened, and adjust the parallelism of No.1 and No.2
scanner units.
13) Tighten the set screw of the scanner unit drive pulley.
14) Check the image distortion in the same manner as step
10).
Repeat procedures 11) to 14) until horizontal image distor-
tion is eliminated.
VII. Troubles caused by improper adjustment
b. Vertical image distortion adjustment
I. Summary
This adjustment is to adjust parallelism of the vertical optical axis
of the copier and that of each mirror to eliminate vertical image
distortion.
For adjusting vertical image distortion, the overall adjustment
and the right-left balance adjustment must be performed inde-
pendently.
The overall adjustment is performed by changing the height of
No.4/5 mirror unit in the front frame side. The right-left balance
adjustment is performed by changing the right-left balance of
No.2 scanner unit rail.
The right-left balance adjustment must be performed in advance
to the overall adjustment.
II. Purpose
The purpose of this adjustment is to set parallelism of the verti-
cal optical axis of the copier and that of No.4/5 mirror unit and
No.2 mirror unit to eliminate vertical image distortion.
III. Note
Before performing this adjustment, the following adjustments
must have been completed.
If not, this adjustment cannot be performed properly.
*
The lens unit right angle adjustment
*
No.4/5 mirror unit right angle adjustment
*
Horizontal image distortion adjustment
IV. Cases when the adjustment is required
1) When No.4/5 mirror unit is disassembled or its part is
replaced.
2) When the scanner unit drive section is disassembled or its
part is replaced.
3) When the copy image is distorted as follows:
V. Necessary tools
*
Screwdriver (+)
*
Screwdriver (–)
*
Scale
*
Test chart for distortion adjustment (Make by yourself.)
Draw a rectangle on A4 or 8 1/2" x 11" paper as shown
below:
Be sure to make four right angles.
LL
LR
Black background
Scanner unit drive pulley
Set screw
Scanner unit drive pulley
Do not move the shaft.
No.2
scanner
unit.
No.1
scanner
unit
Document Copy C Copy D
L
L
LL
L = 10mm
7 – 11
- SERVICE MANUAL 1
- MODEL SF-2314 1
- MODEL SF-2414 1
- MODEL SF-2514 1
- CONTENTS 2
- [1] GENERAL DESCRIPTION 4
- [2] PRODUCT SPECIFICATIONS 5
- 3. Supplies 7
- Storage period: 8
- Upper unit 9
- Lower unit 9
- 6 7 8 14 15 16 17 18 10
- 11 12 13 14 15 16 17 18 19 20 11
- 1. Packing drawing (SF-2514) 16
- 2. Installation 16
- (2) Space around the machine 17
- (3) Installing table 17
- Mirror unit fixing screw 18
- (3) Developer setting 19
- Developer unit 20
- Fixing screw 20
- (step screw) 20
- Mounting screw A 22
- Mounting screw B 22
- Mounting 23
- Multi bypass feeder unit 24
- [5] GENERAL DESCRIPTIONS OF 25
- EACH SECTION 25
- 3. Fuser, paper exit section 26
- 4. Developer section 26
- 5. Optical system 27
- 5-2. Basic operations 28
- 6. Copy process 30
- (3) Actual process 31
- Step 3 (Main Charging) 32
- Step 4 (Exposure) 32
- Step 5 (Development) 33
- Step 6 (Transfer) 34
- Step 7 (Separation) 34
- Step 8 (Cleaning) 35
- Step 9 (Discharging) 35
- (5) Process correction system 36
- 2) Correction operation 36
- [Initial setting] 37
- [Correction timing] 37
- [Correction operation] 37
- 7. SPF section (SF-2514 only) 38
- (Timing chart) 38
- [6] DISASSEMBLY AND ASSEMBLY 39
- 1-3. Separation roller 40
- One-way clutch side 41
- 1-6. Transport belt 42
- 1-7. Socket holder unit 42
- 1-8. Lower unit PWB 42
- 1-10. Power unit 42
- 2. Manual paper feed section 43
- 3. Fuser section 44
- 3-6. Scraper replacement 46
- 4. Optical system 47
- 4-6. Optical unit removal 49
- 5. SPF section 51
- 1, 2." 52
- 5-5. Clutch/solenoid removal 53
- 5-6. Sensor removal 53
- 6. Drum section 54
- 7. Developer section 54
- 7-3. Toner motor removal 55
- 7-4. Toner density sensor 55
- 9-3. Ventilation fan motor 56
- 9-1. Ozone filter 56
- 9-4. Transport roller clutch 57
- 9-5. Paper exit sensor 57
- [7] ADJUSTMENTS 58
- 0.625±0.03mm 59
- 2. Optical section 60
- Document Copy 63
- Document Copy A Copy B 64
- Cam fixing screw 65
- Do not move 65
- No.2 scanner unit 67
- Positioning plate 67
- Scanner unit drive pulley 67
- Document Copy C Copy D 68
- Change the right side 69
- Change the left side 69
- Copy paper 70
- Optical unit cover 71
- Copy image size 73
- Original size 73
- (7) Uniformity adjustment 75
- Paper exit 76
- Half-tone copy 76
- Less exposure 76
- (Dark copy) 76
- Scale image lead edge 78
- Enlargement copy (x 1.54) 78
- Reduction copy (x 0.64) 79
- Copy scale image 80
- Paper lead edge 80
- current void area (mm) 81
- 3. COPY DENSITY ADJUSTMENT 83
- Not copied 84
- Slightly copied 84
- adjustment 85
- Charger wire 87
- Improper 87
- [8] SIMULATIONS 88
- 4. Purpose list 89
- 5. Details of simulations 90
- ÷ Document length x 100 [%] 94
- EXP1~5 voltage 98
- Full power 98
- 6. User simulation 100
- Auto start function 101
- (2) User simulation prcedure 101
- (3) User program code table 102
- [9] SELF DIAG 103
- 4. Self diag contents 104
- 1) Paper feed section 109
- 2) Transport section 109
- [10] SERVICING AT MEMORY 110
- TROUBLE AND MAIN 110
- CONTROL PWB REPLACEMENT 110
- 4. Set value recording sheet 113
- 5. Memory simulation list 114
- [11] MAINTENANCE 115
- [12] ELECTRICAL SECTION 116
- M37702M2-XXXFP 117
- 3 Block diagram 118
- IN XIN IN Clock IN 119
- OUT XOUT OUT Clock OUT 119
- H=+32V, VB=+24V 120
- 1 General 121
- Stepping motor time chart 122
- External view 5P5 123
- Delay capacity 123
- V3' 124
- (1) Outline 126
- (2) Display circuit 127
- 1 Block diagram 127
- 2 Operation 127
- (3) LED display 128
- • AC PWB unit 128
- • In the main PWB unit 129
- COPYRIGHT 131
- 1997 BY SHARP CORPORATION 131
Related products and manuals for Copiers Sharp SF-2414
Copiers Sharp Multi Access User Manual
(12 pages)
(12 pages)
Copiers Sharp AL-2020 User Manual
(32 pages)
(32 pages)
Copiers Sharp MX-M503 User Manual
(12 pages)
(12 pages)
Copiers Sharp AR-CF2 User Manual
(12 pages)
(12 pages)
Copiers Sharp AR-M160 Specifications
(33 pages)
(33 pages)
Copiers Sharp FO-DC550 Specifications
(116 pages)
(116 pages)
Copiers Sharp AR-D25 User Manual
(6 pages)
(6 pages)
Copiers Sharp MX-C310 User Manual
(12 pages)
(12 pages)
Copiers Sharp FO-2080 Specifications
(41 pages)
(41 pages)
Copiers Sharp AL-1631 Specifications
(100 pages)
(100 pages)
Copiers Sharp AR-235 Operations Instructions
(130 pages)
(130 pages)
Copiers Sharp AL-1555 Series Specifications
(89 pages)
(89 pages)
Copiers Sharp FO-155 Specifications
(187 pages)
(187 pages)
Copiers Sharp Multi Access User Manual
(12 pages)
(12 pages)
Copiers Sharp AL-1551CS Specifications
(54 pages)
(54 pages)
Copiers Sharp AR-C170M User Manual
(28 pages)
(28 pages)
Copiers Sharp AR-FX4 Service Manual
(98 pages)
(98 pages)
Copiers Sharp AR-FX7 Service Manual
(110 pages)
(110 pages)
© 2020, manymanuals.com. All rights reserved. | 0.159 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals