Sharp AR-5316 Specifications download pdf (Page 18)

AR-5316 SIMULATIONS 7-2

4. Contents of simulations

50 01 Image lead edge adjustment

06 Copy lead edge position adjustment (SPF)

10 Paper off-center adjustment

12 Document off-center adjustment

51 02 Resist amount adjustment

53 08 SPF scanning position automatic adjustment

10 SPF scan position change-over setting

61 03 HSYNC output check

63 01 Shading check

07 SPF automatic correction

64 01 Self print

Main

code

Sub

code

Contents

Main

code

Sub

code

Contents Details of operation

01 06 Mirror scanning operation aging When the [START] key is pressed, the mirror base performs A3(11” x 17”) full scanning at the set

magnification ratio speed. During scanning, the set magnification ratio is displayed. After 3 seconds,

the mirror base performs full scanning again. During scanning, the set magnification ratio is

displayed.

* When the [START] key is pressed again, the ready lamp turns and remains off.

The DV replacement/OPC drum cartridge replacement lamp displays the status of the mirror

home position sensor. (The lamp lights up when the mirror is in the home position.)

During aging, the copy lamp lights up. When the [Interrupt] key is pressed, the operation is

interrupted if operating, and the machine goes into the sub code input standby mode.

02 01 Single paper feeder (SPF) aging When the [START] key is pressed, the set magnification ratio is acquired and document transport

operation of single surface is performed in the case of SPF. During operation, the LED on the display

section corresponding to the selected magnification ratio lights up, and the magnification ratio is

displayed on the 7-seg display. When the [Interrupt] key is pressed at that time, the machine goes to

the sub code input standby mode. When the [CA] key is pressed, the simulation is terminated.

02 SPF sensor status display (In order to receive the sensor change notification, the load must be decreased.)

The sensor status (ON/OFF) in the SPF can be checked with the following lamps.

When a sensor detects paper, it turns on. The open/close detection sensor turns on when the

machine is opened.

When the [Interrupt] key is pressed, the machine goes to the sub code input standby mode.

When the [CA] key is pressed, the simulation is terminated.

06 01 Paper feed solenoid operation

check

When this simulation is executed, the sub code is displayed on the 7-seg LED and the lamp

corresponding to the solenoid lights up.

Select a solenoid with the tray select key (the lamp corresponding to the solenoid lights up) and

press the [START] key, and the machine repeats operation of ON for 500ms and OFF for 500ms.

This operation is repeated 20 times.

After that, the machine goes into the sub code entry standby mode.

When [INTERRUPT] key is pressed during the process, the machine goes into the sub code input

standby mode. When [CA] key is pressed, the simulation is terminated.

Display lamp Sensor

Toner supply lamp

Copier jam lamp

The DV replacement/OPC drum cartridge

replacement lamp

Paper empty lamp

SPF jam lamp

Manual paper feed lamp

Tray jam lamp

AE lamp

TEXT lamp

PHOTO lamp

SPF document set sensor

SPF document transport sensor

SPF unit (OC cover) open/close sensor

SPF paper exit sensor

SPF paper feed cover open/close sensor

SPF paper length sensor 1

SPF paper length sensor 2

SPF paper feed width sensor (small)

SPF paper feed width sensor (middle)

SPF paper feed width sensor (large)

Display lamp Solenoid

Main cassette lamp

Manual paper feed lamp

Main cassette paper feed solenoid

Manual paper feed solenoid

[07]SIMULATIONS.fm 2 ページ２００５年７月１日金曜日午後５時２８分

1 2 ... 13 14 15 16 17 18 19 20 21 22 23 ... 55 56

Comments to this Manuals

No comments

Sharp AR-5316 Specifications Page 18

Comments to this Manuals

Related products and manuals for Copiers Sharp AR-5316