Sharp AR-5316 Specifications Page 1

This document has been published to be used forafter sales service only.The contents are subject to change without notice.Parts marked with “ “ are im

AR-5316 ADJUSTMENT 6-39) Measure the distance H between the paper lead edge and the imageprint start position. Set the image print start position set

AR-5316 ADJUSTMENT 6-4c.Rear edge void adjustment (SIM50-1, SIM50-19)1) Set a scale as shown in the figure below.2) Set the document size to A4 (8.5&q

AR-5316 ADJUSTMENT 6-52) Loosen the copy lamp unit wire fixing screw.3) Manually turn the mirror base drive pulley and bring No. 2/3 mirrorbase unit i

AR-5316 ADJUSTMENT 6-6(3)Main scanning direction (FR direction) distortion adjustmentThis adjustment must be performed in the following cases:•When th

AR-5316 ADJUSTMENT 6-71) Making of a test sheet Make test sheet by drawing parallel lines at 10mm from the bothends of A3 (11" x 17") white

AR-5316 ADJUSTMENT 6-8<Adjustment specification>Note: A judgment must be made with 200mm width, and must not bemade with 100mm width.(6) Sub sca

AR-5316 ADJUSTMENT 6-9b. SPF original off-center adjustment (SIM50-12)Note:Before performing this adjustment, be sure to check that the paperoff cente

AR-5316 SIMULATIONS 7-1[7] SIMULATIONS1. Entering the simulation modePerform the following procedure to enter the simulation mode."#" key

AR-5316 SIMULATIONS 7-24. Contents of simulations50 01 Image lead edge adjustment06 Copy lead edge position adjustment (SPF)10 Paper off-center adjust

AR-5316 SIMULATIONS 7-306 02 Resist roller solenoid operation checkWhen the [START] key is pressed in the sub code input state, the resist solenoid (R

CONTENTS[1] GENERAL1. Note for servicing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1[2] SPECIFICATIONS1. Copy mode . . . . . . . .

AR-5316 SIMULATIONS 7-422 14 P-ROM version display The P-ROM version is displayed on the copy quantity display. The main code and the sub code are alt

AR-5316 SIMULATIONS 7-546 19 Exposure mode setting (Gamma table setting / AE operation mode setting / PHOTO image process setting)Used set for the fol

AR-5316 SIMULATIONS 7-649 12 Standby mode fusing fan RPM settingWhen this simulation is executed, the currently set code number is displayed. When [MO

AR-5316 USER PROGRAMS 8-1[8] USER PROGRAMSThe user programs allow the parameters of certain functions to be set, changed, or canceled as desired.1. Li

AR-5316 USER PROGRAMS 8-2Program nameProgram NoDescription Default ParametersKey auto repeat25Use this setting to select whether or not holding down a

AR-5316 TROUBLE CODE LIST 9-1[9]TROUBLE CODE LIST1.Trouble code list2.Details of trouble codesMain code Sub codeContentE1 00 IMC PWB communication tro

AR-5316 TROUBLE CODE LIST 9-2E1 82 Content Interface error (Overrun) in communication with the IMC PWBDetail An overrun error occurs in communication

AR-5316 TROUBLE CODE LIST 9-3F5 02 Content Copy lamp lighting abnormalityDetail The copy lamp does not turn on. Cause Copy lamp abnormalityCopy lamp h

AR-5316 TROUBLE CODE LIST 9-4L4 01 Content Main motor lock detectionDetail The main motor does not rotate. The motor lock signal is detected for 1sec

AR-5316 MAINTENANCE 10-1[10] MAINTENANCE1. Maintenance tableX:Check(Clean, adjust, or replace when required.) O:Clean :Replace :Adjust :Lubricate2.

AR-5316 GENERAL 1-1[1] GENERAL1. Note for servicingPictogramThe label ( ) in the fusing area of the machine indicates thefollowing: : Caution, risk

AR-5316 DISASSEMBLY AND ASSEMBLY 11-1[11]DISASSEMBLY AND ASSEMBLYWARNING Before performing the disassembly procedure, be sure toremove the power cord

AR-5316 DISASSEMBLY AND ASSEMBLY 11-22.Optical sectionNote: When disassembling or assembling the optical unit, be careful notto touch the mirror and t

AR-5316 DISASSEMBLY AND ASSEMBLY 11-3E.Lens unitNote:Do not remove screws which are not indicated in the figure. If theheight of the base plate is cha

AR-5316 DISASSEMBLY AND ASSEMBLY 11-43.Fusing section A.Fusing unit removalB.ThermostatC.ThermistorInstallation: When installing the thermistor, be su

AR-5316 DISASSEMBLY AND ASSEMBLY 11-5Assembly: Put the fusing harness (A) on the heater lamp (B) as shownin the figure and fix them together.<R>

AR-5316 DISASSEMBLY AND ASSEMBLY 11-6G.Lower heat rollerAssembly: When installing the paper guide (3) before fusing, fix thepaper guide fixing plate w

AR-5316 DISASSEMBLY AND ASSEMBLY 11-7C.Paper exit unit D.Paper exit sensor(A)Exit sensorE.Transport roller(2)(4)(2)(2)(2)(1)(3)(1)(2)(3)(3)(1)(3)(2)(5

AR-5316 DISASSEMBLY AND ASSEMBLY 11-8F.Paper exit rollerAssembly: Insert the spring pin so that the waveform (A) of the springpin faces in the longitu

AR-5316 DISASSEMBLY AND ASSEMBLY 11-97. LSUA. LSU unitNote:Do not disassemble the LSU.Note:When replacing the LSU, be careful not to touch the dust-sh

AR-5316 DISASSEMBLY AND ASSEMBLY 11-10B.Drive unitAssembly: Move down the clutch pawl as shown below, and avoid theclutch and install. C. Solenoid (pa

AR-5316 SPECIFICATIONS 2-1[2] SPECIFICATIONSThe table below shows the specifications of this model and the contents of changes from the AR-M160/M205 a

AR-5316 DISASSEMBLY AND ASSEMBLY 11-119.Manual multi paper feed section A.Manual transport roller/Manual paper feed rollerNote:Push the lever at the r

AR-5316 DISASSEMBLY AND ASSEMBLY 11-12D. Manual transport clutchE.Pressure plate unitF. Manual paper feed clutchNote: Push the lever at the right edge

AR-5316 DISASSEMBLY AND ASSEMBLY 11-1310.Power sectionA.Power unitB. Power fanC. High voltage P.W.B.D. Power P.W.B.E. Power switchNo. ContentA Power u

AR-5316 DISASSEMBLY AND ASSEMBLY 11-1411.Developing section A.Developing boxB.Developing doctorAdjustment: Developing doctor gap adjustmentC.MG roller

AR-5316 DISASSEMBLY AND ASSEMBLY 11-1512.Process sectionA.Drum unitB. Main charger unitC.Cleaning blade13.OthersA. Operation P.W.B.No. ContentsA Drum

AR-5316 DISASSEMBLY AND ASSEMBLY 11-16B. Tray interface P.W.B.C. Main motorD. I/F P.W.B.(1)(1)(1)(2)(1)(2)(1)(1)(1)(1)(1)(1)(1)(2)(2)(2)(1)(1)(3)(1)(2

AR-5316 DISASSEMBLY AND ASSEMBLY 11-17E. Paper entry sensorF. Paper empty sensorG. Paper feed roller* When removing the paper feed roller, operate th

AR-5316 FLASH ROM VERSION UP PROCEDURE 12-1[12]FLASH ROM VERSION UP PROCEDURE1.PreparationWrite the download data (the file with the extension dwl) to

AR-5316 FLASH ROM VERSION UP PROCEDURE 12-27) PC side: Double click "Special (MCU/MCU2/FAX)" in the main tree item todevelop the sub tree it

AR-5316 FLASH ROM VERSION UP PROCEDURE 12-33) Check that the following display is shown. Select "Install from a list or the specific location&qu

AR-5316 EXTERNAL VIEWS AND INTERNAL STRUCTURES 4-1[4] EXTERNAL VIEWS AND INTERNAL STRUCTURES1. Appearance2. Internal1 Glass cleaner 2 Document feeder

AR-5316 FLASH ROM VERSION UP PROCEDURE 12-43) Check that the new hardware search wizard is shown. Press theNEXT button. 4) Select "Serch for a

AR-5316 ELECTRICAL SECTION 13-1[13] ELECTRICAL SECTION1. Block diagramScanner UnitCCD PWB5V A5V 3.3VB/W8bits(MSB/LSB)5VADCCLK,SYNCH,BSAMP,VSAMPSDI,SCL

AR-5316 ELECTRICAL SECTION 13-23. Actual wiring diagramACTUAL WIRING DIAGRAM 1/7B03P-VL(WHITE)B4B-PH-K-BL(BLACK)SPF GROUND WIREORIGINAL TRAY HARNESSSE

LEAD-FREE SOLDERThe PWB’s of this model employs lead-free solder. The “LF” marks indicated on the PWB’s and the Service Manual mean “Lead-Free” solder

COPYRIGHT 2005 BY SHARP CORPORATION All rights reserved.Printed in Japan.No part of this publication may be reproduced,stored in a retrieval system,

AR-5316 EXTERNAL VIEWS AND INTERNAL STRUCTURES 4-23. Operation Section1 ON LINE key/indicator 2 DUAL PAGE COPY key/indicator 3 XY-ZOOM key/indicator4

AR-5316 UNPACKING AND INSTALLATION 5-1[5]UNPACKING AND INSTALLATION5. Changing a tray's paper size settingFollow these steps to change a tray&apo

AR-5316 ADJUSTMENT 6-1[6]ADJUSTMENTS1.Adjustment item list2.Copier adjustmentA.Process section (1) Developing doctor gap adjustment1) Loosen the devel

AR-5316 ADJUSTMENT 6-2(3)Developing bias voltage checkNote:Use a digital multi-meter with an internal resistance of 10MΩ ormore.1) Set the digital mul