Sharp AR-5316 Specifications Page 11
- Page / 56
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
AR-5316 ADJUSTMENT 6-4
c.Rear edge void adjustment (SIM50-1, SIM50-19)
1) Set a scale as shown in the figure below.
2) Set the document size to A4 (8.5" x 11"), and make a copy at 100%.
3) If necessary, perform the following adjustment procedure.
4) Execute SIM 50-1 and set the density mode to AUTO + TEXT +
PHOTO (Rear edge void).The currently set adjustment value is
displayed.
5) Enter the set value and press the start key. The correction value is
stored and a copy is made.
<Adjustment specification>
d. Paper off center adjustment (SIM50-10)
1) Set a test chart (UKOG-0089CSZZ) on the document table.
2) Select a paper feed port and make a copy. Compare the copy and
the test chart. If necessary, perform the following adjustment
procedure.
3) Execute SIM 50-10. After completion of warm-up, shading is
performed and the currently set off center adjustment value of each
paper feed port is displayed.
4) Enter the set value and press the start key. The correction value is
stored and a copy is made.
<Adjustment specification>
e.Side edge void area adjustment (SIM26-43)
Note:Before performing this adjustment, be sure to check that the paper
off center adjustment (SIM 50-10) is completed.
1) Set a test chart (UKOG-0089CSZZ) on the document table.
2) Select a paper feed port and make two copies. Compare the 2nd
copy and the test chart. If necessary, perform the following
adjustment procedure.
* The 1st copy does not show the void. Be sure to check the 2nd copy.
3) Execute SIM 26-43 and set the density mode to AUTO(right edge
void) + TEXT (Left edge void).
The currently set adjustment value is displayed.
4) Enter the set value and press the start key. The correction value is
stored.
<Adjustment specification>
* The void adjustment values on the right and the left must be the
same.
(2) Main scanning direction(FR direction) distortion balance
adjustment
1) Remove the OC glass and the right cabinet.
Mode SIM LED Set value Specifi-
cation
Set
range
Rear edge void SIM
50-1
AUTO
+
TEXT
+
PHOTO
1 step:
0.1mm shift
4mm or
less
1 ~ 99
Mode SIM LED Set value Specifi-
cation
Set
range
Paper off
center
SIM
50-10
AUTO
+
Selected
tray ON
Add 1:
0.1mm shift
to R side.
Reduce 1:
0.1mm shift
to L side.
Single:
Center
±2.0mm
1 ~ 99
A4(8.5" x 11")
Paper rear edge
Scale image
Paper rear edge
Void amount (Standard value: 4mm or less)
ode SIM LED Set value Specifi-
cation
Set
range
Left edge void SIM
26-43
AUTO
(right
edge)
+
TEXT
(left edge)
1 step:
0.5mm shift
0.5 ~ 4mm 1 ~ 99
(1)
(1)
(2)
(4)
(3)
(3)
[06]ADJUSTMENT.fm 4 ページ ２００５年７月１日 金曜日 午後５時２７分
- DIGITAL COPIER 1
- CONTENTS 2
- [1] GENERAL 3
- [2] SPECIFICATIONS 4
- [3] CONSUMABLE PARTS 4
- 1. Appearance 5
- 2. Internal 5
- 3. Operation Section 6
- [5]UNPACKING AND INSTALLATION 7
- [6]ADJUSTMENTS 8
- (4) Grid bias voltage check 9
- B.Mechanism section 9
- (1)Image position adjustment 9
- A4(8.5" x 11") 11
- Paper rear edge 11
- Scale image 11
- Wire fixing screw 12
- Rear side 13
- Front side 13
- Paper exit 14
- Parallel line 14
- White paper 14
- Original guide 15
- Copy paper 15
- (A3 or 17" x 11") 15
- C.Image density adjustment 16
- (1)Copy mode (SIM 46-1) 16
- [7] SIMULATIONS 17
- 4. Contents of simulations 18
- [8] USER PROGRAMS 23
- [9]TROUBLE CODE LIST 25
- [10] MAINTENANCE 29
- [11]DISASSEMBLY AND ASSEMBLY 30
- 2.Optical section 31
- (+) direction 32
- ) direction 32
- One division: 1.4mm 32
- 3.Fusing section 33
- E.Upper heat roller 34
- F.Separation pawl 34
- 4.Paper exit section 35
- (A)Exit sensor 36
- 6.Optical frame unit 37
- Grease G-484 39
- Moricote X56020 39
- D. Manual transport clutch 41
- E.Pressure plate unit 41
- F. Manual paper feed clutch 41
- 10.Power section 42
- 11.Developing section 43
- 12.Process section 44
- 13.Others 44
- E. Paper entry sensor 46
- F. Paper empty sensor 46
- G. Paper feed roller 46
- 1.Preparation 47
- 2.Download procedure 47
- 3. Installation procedure 48
- [13] ELECTRICAL SECTION 51
- 3. Actual wiring diagram 52
- Example: 55
- COPYRIGHT 56
- 2005 BY SHARP CORPORATION 56
Related products and manuals for Copiers Sharp AR-5316
Copiers Sharp SF-2414 User Manual
(43 pages)
(43 pages)
Copiers Sharp AR-150 SERIES Specifications
(56 pages)
(56 pages)
Copiers Sharp AR-163 Specifications
(80 pages)
(80 pages)
Copiers Sharp AR-M700 User Manual
(12 pages)
(12 pages)
Copiers Sharp AR-162S User Manual
(2 pages)
(2 pages)
Copiers Sharp SF-1014 Service Manual
(153 pages)
(153 pages)
Copiers Sharp AR-M316 Service Manual
(159 pages)
(159 pages)
Copiers Sharp AR-CF2 Service Manual
(42 pages)
(42 pages)
Copiers Sharp MX-M620U Specifications
(200 pages)
(200 pages)
Copiers Sharp AR-F14N User Manual
(12 pages)
(12 pages)
Copiers Sharp AR-155N Specifications
(56 pages)
(56 pages)
Copiers Sharp FO-781 Instruction Manual
(208 pages)
(208 pages)
Copiers Sharp AR-5220 Specifications
(19 pages)
(19 pages)
Copiers Sharp AR-NB2N User Manual
(4 pages)
(4 pages)
Copiers Sharp AR-162S Specifications
(68 pages)
(68 pages)
Copiers Sharp Z-26 User Manual
(32 pages)
(32 pages)
Copiers Sharp SF-2040 User Manual
(95 pages)
(95 pages)
© 2020, manymanuals.com. All rights reserved. | 1.885 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals