Sharp AR-168N Specifications Page 80
- Page / 177
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
AR-168N/168L TEST COMMAND, TROUBLE CODES 10 - 5
5 01 Operation panel display
check (LCD/LED CHK)
[Function]
<LED check mode (All ON/Individual ON)>
When [ENTER/START] key is pressed, all the LCD's on the operation panel are turned ON (all pixels
ON).
After 5sec of ON, the machine goes into the sub code entry standby mode.
When [MODE SWITCH] key is pressed under the all ON state, the mode is shifted to the individual
ON mode, where the LED's are turned on one by one from the left upper end to the left lower side
then from the right upper side to the right lower side. (All the pixels of LCD are lighted simultaneously.)
After lighting all the LCD's sequentially, all the LCD's are lighted simultaneously. After 5sec from light-
ing all the LCD's simultaneously, the machine goes into the sub code entry standby mode. (Cycle of
individual ON mode: ON 300ms, OFF 20ms)
When [C] key is pressed in the LED check mode, the machine goes into the sub code entry standby
mode.
When [START] key is pressed, the machine goes into the key input check mode.
<Key input check mode>
When the machine goes into the key input check mode, the LCD displays 0.
When any key is pressed after pressing a key on the operation panel, "+1" is added to the value.
Once a key is pressed, it is not recounted.
When [START] key is pressed, counting is made and the machine goes into the LED ON check mode
(LED all ON status) after 3sec.
When [C] key is pressed for the first time, it is counted. When it is pressed for the second time, the
machine goes into the sub code entry mode.
When [CA] key is pressed for the first time, it is counted. When it is pressed for the second time, the
machine goes out from the test command mode.
(Note in the key input check mode)
• Be sure to press [START] key at the last. (If it is pressed on the way, the machine goes into the LED
ON check mode.) (LED all ON status)
• Multi key input is ignored.
[Operation]
<LED check mode (All ON/Individual ON)>
<Key input check mode>
02 Fusing lamp, cooling fan
operation check (HT LAMP
CHK)
[Function]
When [ENTER/START] key is pressed, the fusing lamp repeats ON for 500ms and OFF for 500ms 5
times. During this period, the cooling fan motor rotates.
[Operation]
03 Copy lamp ON check
(C-LAMP CHK)
[Function]
When [ENTER/START] key is pressed, the copy lamp turns ON for 5sec.
[Operation]
Main
code
Sub
code
Contents Details of function/operation
1) Initial display
2) When [MODE SWITCH] key is pressed, the machine goes into the individual ON mode.
■■■■■■■■■■■■■■■■■■■■■
■■■■■■■■■■■■■■■■■■■■■
1) Initial display 2) [ENTER/START]
05-01 LCD/LED CHK.
0
05-01 LCD/LED CHK.
**
1) Initial display
05-02 HT LAMP CHK
EXECUTING...
1) Initial display
05-03 C-LAMP CHK
EXECUTING...
10_TESTCOMMAND.fm 5 ページ ２００５年１１月１８日 金曜日 午後５時３７分
- DIGITAL MULTIFUNCTIONAL 1
- CAUTION 2
- CONTENTS 4
- [1] GENERAL 6
- [2] SPECIFICATIONS 7
- 3. Copy performance 8
- 4. SPLC printer 9
- 5. Scan function 9
- [3] CONSUMABLE PARTS 10
- 4. TD cartridge replacement 11
- 1. Appearance 12
- 2. Internal 12
- 18 19 20 21 13
- 4. Motors and solenoids 14
- 5. Sensors and switches 15
- 6. PWB unit 16
- 7. Cross sectional view 17
- 1. Copier installation 18
- 2. Cautions on handling 18
- Lock Unlock 19
- Grasp here and turn in 19
- CAUTION tape 19
- Protective pins 19
- Pressure plate lock 21
- [Custom installation] 23
- (1) Windows XP (USB/Parallel) 23
- (2) Windows 98/Me/2000 (USB) 24
- C. Setting up button manager 27
- (1) Windows XP 27
- (2) Windows 98/Me/2000 27
- (1) Connecting a USB cable 28
- 11. Interface 29
- 12. Moving 29
- [6] COPY PROCESS 30
- 2. Outline of print process 31
- 3. Actual print process 31
- About DC 5.2kV 32
- Process controlling 33
- [7] OPERATIONAL DESCRIPTIONS 34
- 34 6 285 35
- 3. Laser unit 36
- 4. Fuser section 36
- (1) Heat roller 37
- (2) Separator pawl 37
- (3) Thermal control 37
- (4) Fusing resistor 37
- A. Initial state 41
- B. Front copy 41
- C. Back copy 41
- 8. Shifter 42
- [8] DISASSEMBLY AND ASSEMBLY 43
- Example of NG 44
- Charger wire 46
- Protrusion 46
- 3. Optical section 47
- CCD core 48
- 4. Fusing section 49
- Heat roller disassembly 50
- Heater lamp 50
- C. Assembly procedure 56
- Back Wire treatment 57
- 7. Rear frame section 59
- 8. Power section 60
- 9. Duplex motor section 60
- (1) Remove the rear cabinet 61
- (2) Remove the RSPF 61
- F. Sensor PWB 62
- G. Pickup solenoid 62
- H. Clutch 62
- (1) Remove the clutch unit 62
- (2) Remove the clutch 63
- (1) Remove the pickup unit 63
- (1) Remove the parts 65
- (2) Remove the parts 66
- T. Solenoid 67
- (1) Remove the reverse gate 67
- (2) Remove the solenoid 67
- [9] ADJUSTMENTS 68
- B. Image position adjustment 69
- (1) Lead edge adjustment 69
- B4 or 8 1/2″ × 14″ paper 70
- A4 size rear edge 70
- Scale image 70
- Paper rear edge 70
- White paper 71
- Test chart 71
- 3. High voltage adjustment 72
- 4. Duplex adjustment 72
- Document guide 73
- The trailing edge has a scale 73
- Table glass 73
- Scale (D-D mode) 73
- 6cm or more is required 74
- 2. Key rule 76
- 3. List of test commands 76
- Image loss, R = 4mm 101
- Chart back surface 105
- 5. Trouble codes 114
- [11] MAINTENANCE 117
- [12] USER PROGRAM 118
- B. Print mode 119
- [13] ELECTRICAL SECTION 121
- 2. Circuit descriptions 122
- (4) Reset circuit 127
- ASIC/CPU 128
- Tonner Motor Driver 129
- TD62064AF 130
- (10) OPE PWB 131
- (11) Carriage Unit 131
- (1) Noise filter circuit 131
- Voltage waveform 132
- [14]CIRCUIT DIAGRAM 134
- Serial EE-PROM 135
- MCU PWB (ASIC section) 136
- MCU PWB (Memory section) 138
- MCU PWB (Driver section 1) 140
- MCU PWB (Driver section 2) 142
- MCU PWB (Driver section 3) 144
- MCU PWB (IMC2 section 1/2) 148
- MCU PWB (Connector section 1) 152
- To Operational PWB 153
- To Mirror motor 153
- MCU PWB (Connector section 3) 154
- To 2nd. cassette 155
- MCU PWB (Modem I/F Connector) 157
- MCU PWB (Scanner I/F section) 158
- 2. OPERATION PWB 159
- To MCU PWB 161
- To Drum Initial Detector 161
- To FAX Key PWB 161
- POWER SUPPLY (120V/127V) 162
- (1) MCU SECTION (1/3) 164
- [15] FIRMWARE DOWNLOAD 167
- PROCEDURES 167
- 5. Installing procedures 171
- LEAD-FREE SOLDER 175
- CAUTION FOR BATTERY DISPOSAL 176
- COPYRIGHT 177
- 2005 BY SHARP CORPORATION 177
Related products and manuals for Multifunctionals Sharp AR-168N
Multifunctionals Sharp AR-156 Specifications
(52 pages)
(52 pages)
Multifunctionals Sharp AR-651 Service Manual
(42 pages)
(42 pages)
(2 pages)
Multifunctionals Sharp MX-2600N User Manual
(12 pages)
(12 pages)
Multifunctionals Sharp MX-2010U User Manual
(12 pages)
(12 pages)
Multifunctionals Sharp AL-1043 Service Manual
(216 pages)
(216 pages)
Multifunctionals Sharp AL-841 User Manual
(28 pages)
(28 pages)
Multifunctionals Sharp JW-20FLT User Manual
(224 pages)
(224 pages)
Multifunctionals Sharp MX-4112N User Manual
(12 pages)
(12 pages)
Multifunctionals Sharp AR-151 Specifications
(52 pages)
(52 pages)
Multifunctionals Sharp AR-810 User Manual
(101 pages)
(101 pages)
(2 pages)
Multifunctionals Sharp MX-M753U User Manual
(12 pages)
(12 pages)
Trekstor 76816 Handbücher
Bedienungsanleitungen und Benutzerhandbücher für MP3 / MP4-Player Trekstor 76816.
Wir stellen 1 PDF-Handbücher Trekstor 76816 zum kostenlosen herunterladen nach Dokumenttypen zur Verfügung Datenblatt
Trekstor 76816 Datenblatt (2 Seiten)
Marke: Trekstor | Kategorie: MP3/MP4 players | Größe: 0.63 MB |
Inhaltsverzeichnis
Weitere Produkte und Handbücher für MP3 / MP4-Player Trekstor
| Modelle | Dokumententyp |
|---|---|
| 78012 |
Datenblatt
Trekstor i.Beat GhettoBlaster mini,
2 Seiten
|
| 78512 |
Datenblatt
Trekstor i.Beat GhettoBlaster,
2 Seiten
|
| 74010 |
Datenblatt
Trekstor i.Beat p!nk 1GB pink,
2 Seiten
|
| 76116 |
Datenblatt
Trekstor i.Beat move M,
2 Seiten
|
| 75724 |
Datenblatt
Trekstor i.Beat move M,
2 Seiten
|
| 76024 |
Datenblatt
Trekstor i.Beat move S 8GB chrom,
2 Seiten
|
| 75816 |
Datenblatt
Trekstor i.Beat move L,
2 Seiten
|
| 101045 |
Datenblatt
Trekstor i.Beat mood FM 2 GB,
2 Seiten
|
| 71810 |
Datenblatt
Trekstor 1GB i.Beat cebrax FM,
2 Seiten
|
| 71816 |
Datenblatt
Trekstor i.Beat cebrax 2.0,
2 Seiten
|
| 73810 |
Datenblatt
Trekstor 2GB i.Beat censo,
2 Seiten
|
| 74916 |
Datenblatt
Trekstor i.Beat cody 4GB,
2 Seiten
|
| 74412 |
Datenblatt
Trekstor i.Beat emo 2GB,
2 Seiten
|
| 193354 |
Datenblatt
Trekstor Vibez 12 GB,
2 Seiten
|
| 4016998729249 |
Datenblatt
Trekstor Vibez 8GB,
2 Seiten
|
| 4016998219443 |
Datenblatt
Trekstor i.Beat organix [FM],
2 Seiten
|
| 74612 |
Datenblatt
Trekstor US5 1GB,
2 Seiten
|
| 173824 |
Datenblatt
Trekstor i.Beat motion 2 GB,
2 Seiten
|
| 74312 |
Datenblatt
Trekstor i.Beat sonix 2GB,
2 Seiten
|
| 4016998720109 |
Datenblatt
Trekstor i.Beat vision DM 1 GB,
2 Seiten
|
© 2020, manymanuals.com. All rights reserved. | 0.018 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals