Section-5 Maintenance

October 17, 2013

5‐8

WARNING:Disconnectprimarypower priortoservicing. 888‐2693‐004

Note

RTAC precorrection is automatically disabled and power control is automatically switched to manual

mode during calibration.

5.4.2 ForwardCalibrationProcedure

STEP 1 ZeroandcalibrateRMSpowermeterfollowingthemanufacturer’s

proceduresforspecificmodel.

STEP 2 Locatesystemforwardcalibrationsampleport,whichshouldhavebeen

measuredandlabeledatthefactorywiththecouplingfactorforyour

frequencyofoperation.Thiswilleitherbeaforwardportonthepre‐filter

directionalcoupler,leftavailableforthispurposeinastand‐alone(i.e.non‐

racked)configuration,orth

efrontpanelPRE‐FILTERFWD (forward)power

sampleinarackedconfiguration.Ifthecouplingfactorisinquestion,orif

thefrequencyhaschanged,theapplicableforwardcouple rportshouldbe

sweptwithanetworkanalyzertodeterminethecorrectcouplingfactorat

thefrequencyofinterest.Remembertoincludeth

elossintheroutingcables

inthenetworkanalyzermeasurementwhencharacterizingthebulkhead

measurementpoint.

STEP 3 Oncethecouplingvalueisdetermined,enterthisvalueasanoffsetinthe

powermeter,setthemeter’sdisplaytoreadindBm(3digitsissufficient,i.e.

xx.xdBm),andconnectthemeter’ssensortothisport.

Note

Please ensure that the sample level present at this point (max system output, in dBm, minus the coupling

factor) does not exceed the maximum input range of power sensor being used.

STEP 4 IfdualLPUsareinusesettheTCUDriverControltoManual.SelecttheLPU

tobecalibratedastheactiveLPU.

STEP 5 PressandholdtheLowerbuttonfor30secondstoreducetransmitterRF

outputatturn‐on.UsetheTCULowerbuttonfordualsystems.UsetheLPU

LowerbuttonifasingleLPUispresent.

STEP 6 PressTCUOnbuttonifpresent.PressselectedLPUOnbuttonifnoTCUis

presetn.

STEP 7 EntertheForwardcalibrationmenu,eitherfromthefrontpanel(Setup>

XMTRPOWERSETTINGS>POWERCAL>FORWARD)orfromtheWebGUI.

See’SystemCalibration’(leftside)inFigure5‐3onpage5‐6.

1 2 ... 183 184 185 186 187 188 189 190 191 192 193 ... 291 292

Comments to this Manuals

No comments

AEI Security & Communications DigiSender ZX7 manuales

Manuales del propietario y guías del usuario para Receptor AEI Security & Communications DigiSender ZX7.
Ofrecemos 3 manuales en pdf AEI Security & Communications DigiSender ZX7 para descargar gratis por tipos de documentos: Manual de usuario, Guía para resolver problemas

Sharp SD-AT1000W Specifications Page 188

Comments to this Manuals

AEI Security & Communications DigiSender ZX7 manuales

Aei security communications DigiSender ZX7 Manual de usuario (68 paginas)

Tabla de contenidos

Aei security communications DigiSender ZX7 Guía para resolver problemas (20 paginas)

Tabla de contenidos

Aei security communications DigiSender ZX7 Guía para resolver problemas (20 paginas)

Tabla de contenidos

Más productos y manuales para Receptor AEI Security & Communications