Sharp MD-R3 Operations Instructions Page 42
- Page / 48
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
SYMPTOM POSSIBLE CAUSE REMEDY
TROUBLESHOOTING
■ If a problem occurs
If this unit functions abnormally during operation, first check the following items. If the unit continues to function abnormally,
or if an abnormality appears other than listed below, turn off the player’s power and disconnect the AC power plug, then
consult your SHARP dealer or service personnel.
General
SYMPTOM
POSSIBLE CAUSE REMEDY
The clock is wrong. Did a power failure occur? Try setting it again.
When a button is pressed, the unit does
not respond.
Turn the power off and on again, and
then retry the operation.
Radios make unusual noise or the picture
on the TV screen is distorted.
When a radio or TV which uses an in-
door antenna is placed near the unit, the
picture on the TV screen may be dis-
torted or the radio may not function prop-
erly.
It is recommended that you use an out-
door antenna.
MD recording and playback
A recording cannot be made. Is the MiniDisc protected against acci-
dental erasure?
Slide the accidental erase prevention tab
back to its original position.
Did you try to record on a playback-only
MiniDisc?
Replace it with a recordable disc.
Can you see the “TOC FULL” message
in the display?
Put in another recordable disc with re-
cording space on it.
Even though a disc has been loaded,
“NO DISC” or “ERROR” is displayed.
Is the disc scratched?
Is the unit located near excessive vibra-
tion?
Replace the disc.
Place the unit on a firm, level surface
free from vibration.
Playback stops in the middle of a track,
or playback is not performed properly.
Is the unit located near excessive vibra-
tions?
Place the unit on a firm, level surface free
from vibration.
Playback sounds are skipped.
Has condensation formed inside the unit?
Remove the disc and leave the power
turned on. The unit should function prop-
erly in about 1 hour.
Remote control
SYMPTOM POSSIBLE CAUSE REMEDY
The remote control does not function or
does not operate properly.
The batteries (polarity) are not inserted
properly.
Insert properly.
The batteries inside the remote control
are dead.
Replace the batteries.
The remote control is operated from an
incorrect distance or angle.
Operate it within a range of 8" (0.2 m) to
20’ (6 m) and within an angle of 15
o
to
either side of center.
No disc has been loaded. Load a disc.
The power cannot be turned on from the
remote control.
Is the AC power cord plugged in? Connect the AC power cord.
CD playback
SYMPTOM POSSIBLE CAUSE REMEDY
Even though a disc has been loaded, "NO
DISC" or "ERROR" is displayed.
Playback stops in the middle of a track,
or playback is not performed properly.
Playback sounds are skipped.
The disc is loaded up-side down.
Load the disc with the correct side up.
The disc is very dirty. Clean the disc.
The disc does not satisfy the standards. Load the correct disc.
Is the unit located near excessive vibra-
tions?
Place the unit on a firm, level surface free
from vibration.
Has condensation formed inside the unit?
Remove the disc and leave the power
turned on. The unit should function properly
in about 1 hour.
MD-R3
41
- MD/CD DECK 1
- IMPORTANT SAFEGUARDS 2
- ACCESSORIES 2
- CONTENTS 2
- PRECAUTIONS 3
- ■ Front panel 4
- ■ Rear panel 4
- REMOTE CONTROL 5
- Jacks to be connected 6
- SETTING THE CLOCK 9
- ■ Setting the time 10
- 2 Press the MD ■ button 11
- 1 Press the CD ■ button 12
- 5 Press the CD button 12
- CD DIRECT PLAY 13
- Selected track number 14
- 2 Press the PLAY MODE button 15
- (Continued) 16
- ■ Music scan play 17
- RECORDING 19
- ■ APMS recording 22
- ■ Sound synchro recording 23
- ■ To re-record 24
- 2 Press the MD button 25
- 1 2 3 4 5 6 7 26
- 8 9 10 11 12 13 26
- 15 16 17 18 26
- ■ Using the editing function 27
- ■ DIVIDE 28
- ■ COMBINE 29
- NAME/TOC EDIT 31
- ■ Track/disc name 32
- ■ To create a disc name 33
- ■ To erase disc names 33
- ■ To create a track name 34
- ■ To erase track names 34
- ■ To erase a character 36
- ■ To add a character 36
- ■ To correct a spelling 36
- ■ Timer playback 37
- ■ Timer recording 38
- ■ To check the timer setting 39
- ■ Handling the MiniDisc 40
- ■ What is a MiniDisc? 40
- ■ Types of discs 41
- ■ High-speed access 41
- ■ Shock Resistant Memory 41
- ■ If a problem occurs 42
- ■ Moisture condensation 44
- MAINTENANCE 45
- SPECIFICATIONS 45
- LIMITED WARRANTY 48
Related products and manuals for Minidisc players Sharp MD-R3
Minidisc players Sharp MD-MT200H User Manual
(52 pages)
(52 pages)
Minidisc players Sharp MD-MT45H Specifications
(140 pages)
(140 pages)
Minidisc players Sharp MD-MT90H Specifications
(140 pages)
(140 pages)
Minidisc players Sharp MD-MT270H User Manual
(47 pages)
(47 pages)
Minidisc players Sharp MD-M1H Specifications
(52 pages)
(52 pages)
Minidisc players Sharp MD-MT99H User Manual
(56 pages)
(56 pages)
Minidisc players Sharp MD-MT180H User Manual
(51 pages)
(51 pages)
Minidisc players Sharp MD-MT88H User Manual
(56 pages)
(56 pages)
© 2020, manymanuals.com. All rights reserved. | 0.342 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals