Sharp R1514T User Manual download pdf

2 WALL CONSTRUCTION

This Microwave Oven/Hood should be mounted against and supported by a flat vertical wall. The wall must be flat for proper

installation. If the wall is not flat, use spacers to fill in the gaps. Wall construction should be a minimum of 2” x 4” wood studding and

3/8” or more thick dry wall or plaster/lath. The mounting surfaces must be capable of supporting weight of 110 pounds—the oven

and contents—AND the weight of all items which would normally be stored in the top cabinet above the unit.

The unit should be attached to a minimum of one 2” x 4” wall stud.

To find the location of the studs, one of the following methods may be used:

A. Use a stud finder, a magnetic device which locates the nails in the stud.

B. Use a hammer to tap lightly across the mounting surface to find a solid sound. This will indicate stud location.

The center of the stud can be located by probing the wall with a small nail to find the edges of the stud and then placing a mark

halfway between the edges. The center of any adjacent studs will normally be 16” or 24” to either side of this mark.

OVER THE RANGE MICROWAVE OVEN/HOOD SYSTEM

INSTALLATION INSTRUCTIONS

Please read all instructions thoroughly before installing the Microwave Oven/Hood System.

Two people are recommended to install this product.

If a new electrical outlet is required, its installation should be completed by a qualified electrician before

the Microwave Oven/Hood is installed. See 3 ELECTRICAL GROUNDING INSTRUCTIONS on page 2.

1 MOUNTING SPACE

This Microwave Oven/Hood requires a mounting space on a

wall as shown in Figure 1. It is designed to be used with standard

12-inch wall cabinets.

If the space between the wall cabinets is 36 or 42 inches, a Filler

Panel Kit can be used to fill the gap. The metal filler panels come

in 3-inch wide pairs. One set is needed for a 36-inch opening and

2 sets for a 42-inch opening. See page 8 for ordering information.

The Filler Panel Kit should be installed before the Microwave Oven/

Hood is installed.

Backsplash

At least 2"

30" or more from

cooking surface

66" or more

from floor

15.5"

30"

12"

Figure 1

1 2 3 4 5 6 7 8

Summary of Contents

Page 1 - INSTALLATION INSTRUCTIONS

12 WALL CONSTRUCTIONThis Microwave Oven/Hood should be mounted against and supported by a flat vertical wall. The wall must be flat for properinstalla

Page 2 - 4 HOOD EXHAUST DUCT

23 ELECTRICAL GROUNDING INSTRUCTIONSThis appliance must be grounded. This oven is equipped with a cord having a grounding wire with a grounding plug.

Page 3 - 7 PREPARATION OF THE OVEN

36 INSTALLATION HARDWAREThe INSTALLATION HARDWARE items1-7 are in a small bag. Items 8-" arepacked separately. All items are in asmall carton pac

Page 4 - Figure 8

48 VENTILATION SYSTEM (PREPARING OVEN FOR INSTALLATION)This Microwave Oven/Hood is designed for adaptation to three types of hood ventilation systems.

Page 5 - Figure 15

5(C) VERTICAL EXHAUST: Outside Ventilation1. Remove and save 2 screws from back edge and 3 screws from the top center of the Fan Cover Bracket. Remove

Page 6 - 9 OVEN INSTALLATION

69 OVEN INSTALLATIONTHIS OVEN CANNOT BE PROPERLY INSTALLED WITHOUT REFERRING TO THE MOUNTING INSTRUCTIONS FOUND ONBOTH TEMPLATES.THE NEXT STEP IS TO R

Page 7 - Figure 22

710 PREPARATION AND USE OF THE CARTON TO ASSIST INTHE INSTALLATION OF THE MICROWAVE OVENUtilization of the carton may make installation easier.1. Plac

Page 8 - MOUNTING OVEN TO THE WALL

8CHECKLIST FOR INSTALLATIONACCESSORIESCheck with your dealer or order directly from the SHARP Accessories and Supplies Center. Call toll-free 1-800-64

Comments to this Manuals

No comments

Sharp R1514T User Manual

Browse online or download User Manual for Microwaves Sharp R1514T. R-1510 | R-1511 | R-1512 | R-1514 Installation Instructions

Summary of Contents

Comments to this Manuals

Related products and manuals for Microwaves Sharp R1514T