"(%"
BdYZa<%+%%B[\#H^cXZ,$&&
10. Ijgc Vcdi]Zg %#%&% d[[ d[ i]Z Y^VbZiZg VcY
X]ZX` [dg V iVeZg# GZeZVi jci^a i]Z YZh^gZY
Vbdjcid[VXXjgVXn^hVX]^ZkZY#
Figure 28.IV^ahidX`VY_jhibZcidei^dc'#
Figure 27.IV^ahidX`VY_jhibZcidei^dc&#
Figure 26.8]jX`XZciZg^c\i]ZYZVYXZciZg#
Aligning Tailstock
To align the tailstock:
1. Jh^c\ V egZX^h^dc aZkZa! bV`Z hjgZ i]Z
WZYlVnh VgZ aZkZa h^YZ"id"h^YZ VcY [gdci"id"
WVX`#>[i]ZaVi]Z^hcdiaZkZa!h]^bi]ZaVi]Z
WVhZVhgZfj^gZYWZ[dgZegdXZZY^c\#
2. <Ziilde^ZXZhd[hiZZagdjcYhidX`i]ViVgZ
'Y^VbZiZgm+^cX]Zhadc\#
3. 8ZciZg Yg^aa Wdi] ZcYh d[ dcZ e^ZXZ d[ i]Z
gdjcY hidX`# HZi i]Z gdjcY hidX` Vh^YZ [dg
jhZ^cStep 6.
4. Jh^c\i]Zdi]Zge^ZXZd[hidX`!bV`ZVYZVY
XZciZg Wn ijgc^c\ V h]djaYZg id bV`Z V
h]Vc`#;a^ei]Ze^ZXZ dkZg^ci]ZX]jX` VcY
ijgcV+%§ed^ciFigure 26.
Note:As long as the dead center remains in
the chuck, the point of your center will remain
true to the spindle axis. But remember the
point will have to be refinished whenever it is
removed and returned to the chuck.
5. EaVXZi]Za^kZXZciZg^ci]ZiV^ahidX`#
6. 6iiVX] V aVi]Z Yd\ id i]Z gdjcY hidX` VcY
bdjci^iWZilZZci]ZXZciZgh.
7. IjgcVeegdm^bViZan%#%&%d[[i]ZY^VbZiZg#
8. BdjciVY^Va^cY^XVidghdi]Zeajc\Zg^hdci]Z
iV^ahidX`WVggZaWZ[dgZbdk^c\i]ZiV^ahidX`#
9. BZVhjgZi]ZhidX`Y^VbZiZgl^i]Vb^Xgdb"
ZiZg#
·>[ i]Z Y^VbZiZg ^h i]^X`Zg Vi i]Z iV^ahidX`
ZcY!bdkZi]ZiV^ahidX`idlVgYndj]Va[d[
i]ZY^VbZiZgFigures 27#
·>[ i]Z Y^VbZiZg ^h i]^ccZg Vi i]Z iV^ahidX`
ZcY!bdkZi]ZiV^ahidX`VlVn[gdbndj]Va[
i]ZY^hiVcXZd[i]ZY^VbZiZgFigure 28#
Comments to this Manuals