Sharp AR-M450 Instruction Manual Page 74
- Page / 92
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
7-2
WHEN A TRANSACTION REPORT IS PRINTED
The machine has been set to automatically print a Transaction Report when a transmission is not successful or when
the Broadcast transmission function is used. The Transaction Report informs you of the result of the operation. When
the machine prints a Transaction Report, be sure to check the contents.
The initial settings (factory settings) for printing Transaction Reports are indicated by shading below. You can
use the key operator program to change the settings (page 8-5).
• Single sending: Print out all report / Print out error report only / No printed report
• Receiving: Print out all report / Print out error report only / No printed report
• Broadcasting: Print out all report / Print out error report only / No printed report
• Confidential reception: Print out notice page / Not print out notice page
The Transaction Report shows the date of transmission, the time transmission began, the other party's name, the
duration of the operation, the number of pages, and the result.
NOTES
• The list count appears in the "#" column of the Transaction Report and a serial number appears in the FILE column. (These
numbers are not related to the transaction.)
• When a transmission error occurs, a portion of the original document is printed along with the Transaction Report. You can
set the machine to not print the original using the key operator program (page 8-5).
■ Information appearing in the TYPE/NOTE column
Information such as the type of transmission and type of error appears in the TYPE/NOTE column of the Transaction
Report. The following notes may appear.
Note Explanation
OK The transaction was completed normally.
G3 Communication took place in G3 mode.
ECM Communication took place in G3 ECM mode.
SG3 Communication took place in Super G3 mode.
FW. The received data was forwarded.
NO RESPONSE No response from the receiving party.
BUSY Transmission was not possible because the other party was already using the line.
CANCEL A transmission was canceled while in progress, or a stored transmission job was canceled.
P. FAIL A power failure occurred during the transaction.
MEMORY OVER The memory became full during quick on-line transmission.
MEM. FULL The memory became full during reception.
LENGTH OVER The transmitted document was over 59" long and therefore could not be received.
ORIGINAL ERROR Manual transmission was not successful because a jam occurred.
PASS# NG The connection was broken because the polling passcode was not correct.
NO RX POLL The machine that was polled does not have a polling function.
RX POLL FAIL The other machine refused the polling operation, or your machine broke the connection
when polled because no data was in memory.
NO F-CODE POLL The other machine refused an F-code polling operation, or your machine broke the connection
when polled because no data was in its F-code memory polling box.
RX POLL# NG Your machine broke the connection because the other machine specified an F-code polling
sub-address that does not exist in your machine.
F PASS# NG
Your machine broke the connection because the other machine sent an incorrect passcode for F-code polling.
BOX NO. NG
Your machine broke the connection because the specified sub-address for an F-code memory box does not exist.
F POLL PASS# NG
Your machine broke the connection because an incorrect passcode was sent for an F-code transmission.
RX NO F-CODE POLL
F-code polling was attempted, however, the other machine did not have an F-code polling memory box.
NO F FUNC
F-code transmission was attempted, however, the other machine does not support F-code communication.
NO F-CODE
An F-code transmission was refused by the other machine because of an incorrect sub-address or other reason.
M. BOX: [xxxxxx] Data was received to a confidential or relay broadcast memory box, or data was sent from a
•••••• memory polling box.
The name of the memory box appears in [xxxxxx], and the type of F-code operation (relay
request reception, polling memory transmission, or confidential reception) appears in ••••••.
FAIL xx(xxxx) The communication handshake signals or image signals were distorted due to line conditions
or other reasons, and communication was not successful.
First two digits of communication error number: Error code from 00 to 31 appears.
Last four digits of communication error number: Codes for use by service technicians.
- LASER PRINTER 1
- ■ WARNING: 2
- ■ CAUTION: 2
- INTRODUCTION 3
- TABLE OF CONTENTS 4
- CONVENIENT METHODS OF USE 5
- FCC NOTICE TO USERS 6
- IMPORTANT SAFETY INFORMATION 7
- NOTICE FOR USERS IN 8
- AVIS POUR NOS 8
- UTILISATEURS AU CANADA 8
- CHAPTER 1 9
- A LOOK AT THE OPERATION PANEL 11
- ■ Condition setting screen 12
- ORIGINALS 14
- LOADING A DOCUMENT 15
- SELECTING THE RESOLUTION 17
- SELECTING THE EXPOSURE 18
- CONVENIENT DIALING METHODS 19
- CHAPTER 2 21
- SENDING A FAX 22
- ■ Quick On-line 24
- ■ Image rotation 24
- TRANSMISSION BY AUTO-DIALING 25
- CANCELING A FAX TRANSMISSION 26
- RECEIVING FAXES 27
- CHAPTER 3 29
- (BROADCAST TRANSMISSION) 30
- USING BROADCAST TRANSMISSION 31
- (TIMER TRANSMISSION) 32
- THE POLLING FUNCTION 33
- USING THE POLLING FUNCTION 34
- USING POLLING MEMORY 35
- PUBLIC BOX 36
- OWN NUMBER SENDING 37
- ■ Selecting Dual Page Scan 38
- USING A PROGRAM 39
- USING THE TRANSFER FUNCTION 40
- CHAPTER 4 41
- TRANSMISSION BETWEEN MACHINES 42
- SUPPORTING F-CODES 42
- BOX IN THE OTHER MACHINE 43
- F-CODE POLLING MEMORY 44
- PROCEDURE FOR F-CODE POLLING 45
- Your machine 46
- The other machine 46
- CONFIDENTIAL MEMORY BOX 47
- Does not match 48
- CHAPTER 5 51
- STAMPING SCANNED ORIGINALS 52
- (VERIFICATION STAMP FUNCTION) 52
- CONNECTING AN EXTENSION PHONE 53
- AUTO RECEPTION 54
- MANUAL RECEPTION 54
- FAX RECEIVE 55
- DIRECTORY 55
- FAX MEMORY:100% 55
- CHAPTER 6 57
- DIAL KEYS AND PROGRAMS 58
- PROGRAMMING 58
- STORING ONE-TOUCH DIAL KEYS 59
- DELETE THE ADDRESS? 61
- SHARP CORPORATION 61
- SHARP CORPORATION 33.MODE 61
- PROGRAMMING A GROUP KEY 62
- SHARP GROUP 63
- STORING A PROGRAM 64
- EDITING AND DELETING PROGRAMS 64
- STORING A GROUP INDEX 65
- CODE MEMORY BOXES 66
- OF TRANSMISSIONS) 67
- MEMORY BOXES (PRINT PIN.) 68
- SENDING ADDRESS LIST 70
- PRINTER TEST PAGE 70
- ALL CUSTOM SETTING LIST 70
- ENTERING CHARACTERS 71
- Touch the AB/ab 12#$% key 72
- CHAPTER 7 73
- PROBLEMS AND SOLUTIONS 76
- CHAPTER 8 77
- KEY OPERATOR PROGRAMS 78
- SETTING PROGRAMS 79
- Fax default settings 80
- Volume: Volume: Volume: 81
- Low Medium High 81
- Fax send settings 82
- Fax receive settings 84
- Fax polling security 85
- PRINTING OUT SETTINGS 86
- CHAPTER 9 87
- SPECIFICATIONS 88
- Operation Manual 92
Related products and manuals for Print & Scan Sharp AR-M450
Print & Scan Sharp AR-NB3 User Manual
(8 pages)
(8 pages)
Print & Scan Sharp MX-M200D User Manual
(8 pages)
(8 pages)
Print & Scan Sharp DP-750 Service Manual
(240 pages)
(240 pages)
Print & Scan Sharp ER-01PU User Manual
(6 pages)
(6 pages)
Print & Scan Sharp AR-RB1 User Manual
(8 pages)
(8 pages)
Print & Scan Sharp MX-2700G Specifications
(127 pages)
(127 pages)
Print & Scan Sharp CD-M4000 User's Guide
(217 pages)
(217 pages)
Print & Scan Sharp ER-A440 Service Manual
(108 pages)
(108 pages)
Print & Scan Sharp MX-B201D User Manual
(4 pages)
(4 pages)
Print & Scan Sharp MX-2310U Service Manual
(191 pages)
(191 pages)
Print & Scan Sharp ER-A440 User Manual
(38 pages)
(38 pages)
Print & Scan Sharp MX-2310U User Manual
(8 pages)
(8 pages)
Print & Scan Sharp ER-01PU User Manual
(44 pages)
(44 pages)
Print & Scan Sharp MX-M904 User Manual
(12 pages)
(12 pages)
Print & Scan Sharp AR-M355 User Manual
(2 pages)
(2 pages)
Print & Scan Sharp DP-750 Service Manual
(84 pages)
(84 pages)
© 2020, manymanuals.com. All rights reserved. | 0.017 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals