Sharp R-414HS Service Manual

R-414HSIn the interest of user-safety the oven should be restored to its original condition and only parts identical to those specifiedshould be used.

8R-414HSTOUCH CONTROL PANEL ASSEMBLYOUTLINE OF TOUCH CONTROL PANELThe touch control section consists of the following units.(1) Key Unit(2) Control Un

9R-414HS1-2VL2-VL1IN Power source voltage input terminal.Standard voltage for LCD.3-6 AN7-AN4 INTerminal to change cooking input according to the Mode

10R-414HS25 P41 IN Signal similar to AN3.When either G11 line on key matrix is touched, a corresponding signal will be input intoP41.26 P40 IN Connect

11R-414HSConnected to LCD.The relation between signals are as follows:LSI signal (Pin No.) LCD (Pin No.) LSI signal (Pin No.) LCD (Pin No.)SEG0 (72)

12R-414HS645123645123ABCDEFGHABCDEFGHFigure S-1. Pictorial DiagramHIGH VOLTAGECAPACITORHIGH VOLTAGEWIRE AH.V. RECTIFIERPOWER SUPPLY CORD 120V 60HzHIGH

13R-414HS645123645123ABCDEFGHABCDEFGHFigure S-3. CPU Unit Circuit

14R-414HS645123645123ABCDEFGHABCDEFGHFigure S-5 . Printed Wiring Board of Power UnitRY1RY2E C BE C BE C BVRS1L1D7D3PSD4C2D1C1D2R8R7R2R4Q3 Q4SP1T

15R-414HSREF. NO. PART NO. § DESCRIPTION Q'TY CODEPARTS LISTNote: The parts marked “∆∆∆∆∆” may cause undue microwave exposure.The parts marked “*

16R-414HSHOW TO ORDER REPLACEMENT PARTSTo have your order filled promptly and correctly, please furnish the following information.1. MODEL NUMBER2. RE

17R-414HS645123645123ABCDEFGHABCDEFGHOVEN AND CABINET PARTS2-34-76-61-54-64-84-96-46-32-17-51-104-107-27-27-44-31-111-87-37-57-57-64-27-41-91-31-47-11

R-414HSPRECAUTIONS TO BE OBSERVED BEFORE ANDDURING SERVICING TO AVOID POSSIBLEEXPOSURE TO EXCESSIVE MICROWAVEENERGY(a) Do not operate or allow the ove

18R-414HS645123645123ABCDEFGHABCDEFGHCONTROL PANEL PARTS5-1-25-1-15-55-45-35-25-85-15-65-73-33-23-53-13-43-6Actual wire harness may be different from

19R-414HSPACKING AND ACCESSORIESDOOR PROTECTION SHEET PLASTIC BAG PACKING CASE TOP PAD ASSEMBLY INTO THE OVEN CAVITY6-4 TURNTABLE TRAY6-7 OPERATIO

20R-414HSNOTES

21R-414HSNOTES

22R-414HS2003 SHARP CORP. (2M2.00E) Printed in U.S.ACOPYRIGHT © 2003 BY SHARP CORPORATIONALL RIGHTS RESERVED.No part of this publication may be repro-

1R-414HSWARNING TO SERVICE PERSONNELMicrowave ovens contain circuitry capable of pro-ducing very high voltage and current, contact withfollowing parts

2R-414HSMICROWAVE MEASUREMENT PROCEDUREA. Requirements:1) Microwave leakage limit (Power density limit): The power density of microwave radiation emit

3R-414HSSHARP ELECTRONICS CORPORATIONSHARP PLAZA, MAHWAH,NEW JERSEY 07430-2135SUPPLEMENTAL SERVICE MANUALMICROWAVE OVENR-414HSFOREWORDThis supplementa

4R-414HSGENERAL INFORMATIONGROUNDING INSTRUCTIONSThis oven is equipped with a three prong grounding plug. It must be plugged into a wall receptacle th

5R-414HSa qualified electrician and have it replaced with a properly groundedthree-pronged wall receptacle or have a grounding adapter properlygrounde

6R-414HSTEST PROCEDURESPROCEDURELETTERCOMPONENT TESTThe touch control panel consists of circuits including semiconductors such as LSI, ICs, etc. There

7R-414HSJ KEY UNIT TESTTEST PROCEDURESPROCEDURELETTERCOMPONENT TEST6) Reconnect the power supply cord after the outer case is installed.7) Run the ove