Sharp PG-D2510X Setup Guide Page 10
- Page / 76
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
8
Observe the following safeguards when setting up your
projector.
Caution concerning the lamp unit
Potential hazard of glass particles if lamp
ruptures. In case of lamp rupture, contact
your nearest Sharp Authorized Projector
Dealer or Service Center
for replacement.
See “Regarding the Lamp”
on page
56.
Caution concerning the setup of the
projector
For minimal servicing and to maintain high
image quality, SHARP recommends that
this projector be installed in an area free
from humidity, dust and cigarette smoke.
When the projector is subjected to these
environments, the vents and lens must be
cleaned more often. As long as the
projector is regularly cleaned, use in these
environments will not reduce the overall
operation life of the unit. Internal cleaning
should only be performed by a Sharp
Authorized Projector Dealer or Service
Center.
Rest your eyes occasionally.
Continuously watching the screen for long
hours will cause eye strain. Take regular
breaks to rest your eyes.
Do not set up the projector in places
exposed to direct sunlight or bright light.
Position the screen so that it is not in direct
sunlight or room light. Light falling directly
on the screen washes out the colors,
making viewing diffi cult. Close the curtains
and dim the lights when setting up the
screen in a sunny or bright room.
Caution regarding placing of the projector
Place the projector on a level site within the
adjustment range (9 degrees) of the
adjustment foot.
After the projector is purchased, a faint
smell from the vent may appear when the
power is fi rst turned on. This is normal and
is not a malfunction. It will disappear after
the projector is used for a while.
■
■
■
■
■
■
When using the projector in high-
altitude areas such as mountains (at
altitudes of approximately 1,500
meters (4,900 feet) or more)
When you use the projector in high-altitude
areas with thin air, set “Fan Mode” to
“High”. Neglecting this can affect the
longevity of the optical system.
Use the projector at altitudes of 2,300
meters (7,500 feet) or less.
Warning about placing the projector in
a high position
When placing the projector in a high
position, make certain it is carefully secure
to avoid personal injury caused by the
projector falling down.
Do not subject the projector to hard
impact and/or vibration.
Protect the lens so as not to hit or damage
the surface of the lens.
Avoid locations with extremes of
temperature.
The operating temperature of the projector
is from 41°F to 95°F (+5°C to +35°C).
The storage temperature of the projector is
from –4°F to 140°F (–20°C to +60°C).
Do not block the exhaust and intake
vents.
Allow at least 11
13
/
16
inches (30 cm) of
space between the exhaust vent and the
nearest wall or obstruction.
Ensure that the intake vent and the exhaust
vent are not obstructed.
If the cooling fan becomes obstructed, a
protection circuit will automatically put the
projector into Standby mode to prevent
overheat damage. This does not indicate a
malfunction. (See pages 54 and 55.)
Remove the projector power cord from the
wall outlet and wait at least 10 minutes.
Place the projector where the intake and
exhaust vents are not blocked, plug the
power cord back in and turn on the
projector. This will return the projector to
the normal operating condition.
■
■
■
■
■
■
■
■
■
- PG-D2510X 1
- Serial No.: 2
- Model No.: 2
- WARNING: 3
- INFORMATION 4
- PRODUCT DISPOSAL 4
- For Future Reference 5
- Contents 6
- Reference 7
- IMPORTANT SAFEGUARDS 8
- Introduction 11
- fi r s t 12
- Accessories 13
- Part Names and Functions 14
- Inserting the Batteries 17
- Usable Range 17
- Easy Start 18
- Setting Up the Projector 20
- 16:9 Signal Input (16:9 Mode) 21
- Projection (PRJ) Mode 22
- Terminals on the Projector 23
- RCA adaptor plug 24
- (commercially available) 24
- Connections 25
- Connecting the Power Cord 26
- Turning the Projector On/Off 27
- Image Projection 28
- 2 Adjusting the Height 29
- 3 Adjusting the Picture Size 29
- 0KEYSTONE 30
- ADJUST END 30
- Switching the Input Mode 31
- Adjusting the Volume 31
- Displaying the Black Screen 31
- Temporarily 31
- Image Projection (Continued) 32
- About Copyrights 33
- 1/9 1/25 1/8 34
- Useful 35
- Features 35
- Connecting with a USB cable 36
- The mouse pointer can be 36
- Menu Items 37
- (Continued) 38
- Press RETURN to return 40
- To adjust the projected 42
- (Continued) 44
- SEL./ADJ. ENTER END 46
- Pict. SIG-ADJ SCR PRJ1 PRJ2 46
- Fan Mode Setting 52
- System Lock Function 52
- Maintenance 55
- Maintenance Indicators 56
- Appendix 57
- Regarding the Lamp 58
- Removing and Installing the 59
- Lamp Unit 59
- Resetting the Lamp Timer 60
- Connecting Pin Assignments 61
- Computer control 63
- Communication conditions 63
- Basic format 63
- Power ON 65
- Standby mode 65
- (or 30-second startup time) 65
- Compatibility Chart 69
- Troubleshooting 70
- For SHARP Assistance 72
- Specifi cations 73
- Dimensions 74
Related products and manuals for Data projectors Sharp PG-D2510X
Data projectors Sharp XV-Z10E Specifications
(73 pages)
(73 pages)
Data projectors Sharp CMS-R600X User Manual
(70 pages)
(70 pages)
Data projectors Sharp IQ-8000 Specifications
(10 pages)
(10 pages)
Data projectors Sharp AN-CM270 User Manual
(18 pages)
(18 pages)
Data projectors Sharp PG-D2500X Setup Guide
(77 pages)
(77 pages)
Data projectors Sharp CD-E250E User Manual
(16 pages)
(16 pages)
Electrolux ESF2440 manuels
Manuels d'utilisation et guides de l'utilisateur pour Accessoires pour mélangeurs/transformateurs d'aliments Electrolux ESF2440.
Nous fournissons des manuels en pdf 3 Electrolux ESF2440 à télécharger gratuitement par type de document : Manuel de l'utilisateur
Comments to this Manuals