Sharp XG-V10XU User Manual download pdf (Page 4)

E-3

Important

Information

IMPORTANT SAFEGUARDS

AVOID EXPOSURE

LASER

RADIATION IS EMITTED

FROM THIS APERTURE.

CAUTION

LASER RADIATION-

DO NOT STARE INTO BEAM

WAVE LENGTH : 650nm

MAX. OUTPUT : 1mW

CLASS II LASER PRODUCT

"COMPLIES WITH 21 CFR SUBCHAPTER J"

SHARP ELECTRONICS CORPORATION

SHARP PLAZA, MAHWAH, NEW JERSEY 07430

TEL : 1-800-BE-SHARP

U.S.A. ONLY

REMOTE CONTROL

MODEL NO. : RRMCG1564CESA

DC3V (1.5VX2PCS.)

MADE IN CHINA

FABRIQUÉ AU CHINE

The laser pointer on the remote control emits a laser beam from the laser

pointer window. This is a Class II laser which may impair your sight if directed

into the eyes. The three marks shown on the left are caution labels for the

laser beam.

• Do not look into the laser pointer window or shine the laser beam on yourself or

others. (The laser beam used in this product is harmless when directed onto

the skin. However, be careful not to project the beam directly into the eyes.)

• Always use the laser pointer at temperatures between 41°F and 104°F (5°C

and 40°C).

• Use of controls or adjustments, or performance of procedures other than those

specified herein may result in hazardous radiation exposure.

Cautions Concerning the Laser Pointer

Laser pointer

window

Cautions Concerning the Setup of the Projector

For minimal servicing and to maintain high image quality, SHARP recommends

that this projector be installed in an area free from humidity, dust and cigarette

smoke. When the projector is subjected to these environments, the lens must

be cleaned more often. As long as the projector is properly maintained in this

manner, use in these environments will not reduce the overall operation life.

Please note that all internal cleaning must be performed by an Authorized

Sharp Industrial LCD Products Dealer or Service Center.

• The exhaust vent, the lamp cage cover and adjacent areas may be extremely

hot during projector operation. To prevent injury, do not touch these areas until

they have sufficiently cooled.

• Allow at least 4 inches (10 cm) of space between the exhaust vent and the

nearest wall or obstruction.

• If the cooling fan becomes obstructed, a protection device will automatically

turn off the projector lamp. This does not indicate a malfunction. Remove the

projector power cord from the wall outlet and wait at least 10 minutes. Then

turn on the power by plugging the power cord back in. This will return the

projector to the normal operating condition.

Notes on Operation

104˚F

(40˚C)

41˚F

(5˚C)

Caution Concerning the Lamp Replacement

See “Replacing the Lamp” on pages 71 and 72.

LAMP REPLACEMENT CAUTION

BEFORE REMOVING THE SCREW, DISCONNECT

POWER CORD. HOT SURFACE INSIDE ALLOW

1HOUR TO COOL BEFORE REPLACING THE

LAMP. SEE OPERATION MANUAL.

Caution Concerning the Lamp Unit

Potential hazard of glass particles if lamp ruptures. In case of lamp rupture,

contact your nearest Authorized Sharp Industrial LCD Products Dealer or

Service Center for a replacement.

See “Replacing the Lamp” on pages 71 and 72.

CAUTION

POTENTIAL HAZARD OF GLASS

PARTICLES. SEE OPERATION MANUAL.

LAMP MAY RUPTURE.

ATTENTION

LAMPE. DANGER POTENTIEL DE PARTICULES DE

VERRE. SE REPORTER AU MODE D’EMPLOI.

RUPTURE POSSIBLE DE LA

1 2 3 4 5 6 7 8 9 ... 89 90

Comments to this Manuals

No comments

Sharp XG-V10XU User Manual Page 4

Comments to this Manuals

Related products and manuals for Projectors Sharp XG-V10XU