Sharp PG-M10S Service Manual

1PG-M10SU/SEPG-M10XU/XESHARP CORPORATIONDLP PROJECTORDLP PROJEKTORIn the interests of user-safety (Required by safety regulations in some countries) t

10PG-M10SU/SEPG-M10XU/XELouver ScrewTop CoverS-8Louver ScrewDISASSEMBLY AND REASSEMBLY1. Preparations and precautions● Tools required1. Phillips screw

11PG-M10SU/SEPG-M10XU/XE3) Speaker, buttons, etc. (See Fig. 3.)As shown in Fig. 3, remove the nuts, speaker buttonOP, and LED lens. Undo the hooks a

12PG-M10SU/SEPG-M10XU/XE7) Lamp driver (See Fig. 7.)Remove the two screws (S-16 and S-17 each)shown in Fig. 7, and dismount the lamp driver.Lamp Driv

13PG-M10SU/SEPG-M10XU/XE11)Projection lens (See Fig. 11.)Remove the three screws (S-7) shown in Fig. 11,and detach the projection lens.Note: When rea

14PG-M10SU/SEPG-M10XU/XE14)Lamp housing (See Fig. 15.)Remove the three screws (S-7) shown in Fig. 15,and detach the lamp housing from the bottom cove

15PG-M10SU/SEPG-M10XU/XEREPLACING THE LAMP● Tools required1. A soft sheet on which the projector is placed upside down. It is to protect the unit aga

16PG-M10SU/SEPG-M10XU/XEBLOCK DIAGRAM OF OPTICAL SYSTEM PRINCIPLE1235467G B R W●Names of parts and operating specifications1 Lamp2 RGBW color filte

17PG-M10SU/SEPG-M10XU/XEOPTICAL ADJUSTMENT AND MEASURING1.Adjustment of color wheel sensor● Adjustment needed1. When the color wheel unit has been rep

18PG-M10SU/SEPG-M10XU/XE2.Measuring illuminance● Tools required1. Personal computer (run on Windows 95/98)2. Projection screen (normally white)3. Ligh

19PG-M10SU/SEPG-M10XU/XE3.Precautions in disassembling the optical mechanismColor wheelOnce disassembled, this part mayneed readjustment.DMD assemblyT

2PG-M10SU/SEPG-M10XU/XESpecifications

20PG-M10SU/SEPG-M10XU/XESAFETY DEVICE1.Internal temperature detectionThe lamp housing has a built-in thermostat which puts out the lamp when the tempe

21PG-M10SU/SEPG-M10XU/XETROUBLESHOOTING TABLE1.Troubleshooting in generalPower is not supplied.The unit does not go intostand-by mode.Image does not a

43PG-M10SU/SEPG-M10XU/XERef. No. Part No. ★ Description Code Ref. No. Part No. ★ Description CodeBACDEF1 2 3 4 5 6 7 8 9 10BLOCK DIAGRAM / BLOCKSCHALT

44PG-M10SU/SEPG-M10XU/XERef. No. Part No. ★ Description Code Ref. No. Part No. ★ Description CodePRINTED WIRING BOARD ASSEMBLIES(UNIT REPLACEMENT ITEM

45PG-M10SU/SEPG-M10XU/XERef. No. Part No. ★ Description Code Ref. No. Part No. ★ Description Code1 2 3 4 5 6 7 8 9 10ABCDEFGHIJ34765142161715332729183

46PG-M10SU/SEPG-M10XU/XERef. No. Part No. ★ Description Code Ref. No. Part No. ★ Description CodeBACDEF1 2 3 4 5 6 7 8 9 10CABINET AND MECHANICAL PART

47PG-M10SU/SEPG-M10XU/XERef. No. Part No. ★ Description Code Ref. No. Part No. ★ Description CodeBACDEF1 2 3 4 5 6 7 8 9 10656669736472738076747378777

48PG-M10SU/SEPG-M10XU/XERef. No. Part No. ★ Description Code Ref. No. Part No. ★ Description CodeBACDEF1 2 3 4 5 6 7 8 9 10CABINET AND MECHANICAL PART

49PG-M10SU/SEPG-M10XU/XERef. No. Part No. ★ Description Code Ref. No. Part No. ★ Description CodeCABINET AND MECHANICAL PARTS(Continued)BACDEF1 2 3 4

50PG-M10SU/SEPG-M10XU/XERef. No. Part No. ★ Description Code Ref. No. Part No. ★ Description CodeSCREWS, NUTS AND WASHERSS-1 9FU957620020 J Washer, x1

3PG-M10SU/SEPG-M10XU/XENOTE TO SERVICEPERSONNEL UV-RADIATION PRECAUTIONThe light source, metal halide lamp, in the DLPprojector emits small amounts

51PG-M10SU/SEPG-M10XU/XERef. No. Part No. ★ Description Code Ref. No. Part No. ★ Description CodePACKING OF THE SET / VERPACKEN DES GERÄTSPLUS12912712

52PG-M10SU/SEPG-M10XU/XERef. No. Part No. ★ Description Code Ref. No. Part No. ★ Description CodeCOPYRIGHT © 2000 BY SHARP CORPORATIONALL RIGHTS RESER

4PG-M10SU/SEPG-M10XU/XELocation of Controls

5PG-M10SU/SEPG-M10XU/XE

6PG-M10SU/SEPG-M10XU/XEReomte Control

7PG-M10SU/SEPG-M10XU/XEConnections

8PG-M10SU/SEPG-M10XU/XE

9PG-M10SU/SEPG-M10XU/XEPin AssignmentsDimensions