• GETTING STARTED• MAKING COPIES• STATUS INDICATORS• GENERAL INFORMATION2152432DIGITAL COPYING MACHINEOPERATION MANUALMODELAL-1600AL-1610Page
8GETTING STARTED4" (10 cm)Copier installationCOPIER INSTALLATIONImproper installation may damage the copier. Please note the followingduring init
9GETTING STARTEDCAUTIONS ON HANDLINGBe careful in handling the copier as follows to maintain the performance ofthis copier.Do not drop the copier, sub
10GETTING STARTEDCHECKING PACKED COMPONENTSAND ACCESSORIESOpen the carton and check to ensure that the following components andaccessories are include
11GETTING STARTEDSET-UP1Remove all pieces of tape. Then open the platencover and remove the protective material.2Use a coin (or suitable object) to re
12GETTING STARTEDSet-upSET-UPPressureplate lockScrew6Store the pressure plate lock which has beenremoved in step 5 and the screw which has beenremoved
13GETTING STARTED1Gently lift and pull out the paper tray until it stops.2Push the pressure plate down until it locks in place.3Fan the copy paper and
14GETTING STARTEDChanging the copy paper size in the tray1Gently lift and pull out the paper tray until it stops.2Push the pressure plate down until i
24STATUS INDICATORS1Open the bypass tray. Lift slightly on the side cover andslide the cover out until it stops.2Push gently the right side of the fro
25STATUS INDICATORS TD cartridge replacementTD CARTRIDGE REPLACEMENT5Remove the protective cover from the TD cartridge byunlatching three cover hooks
26STATUS INDICATORS1Open the bypass tray. Lift slightly on the side cover andslide the cover out until it stops.2Push gently the right side of the fro
FOR YOUR PROTECTION...To aid in reporting this compact copier in case of loss or theft, please record below themodel number and serial number located
27STATUS INDICATORSDRUM CARTRIDGE REPLACEMENT Drum cartridge replacement5Remove the new drum cartridge from the protective bagand gently insert the le
28STATUS INDICATORSMISFEED REMOVALThe copier will stop when a misfeed occurs. The misfeed ( ) indicator willblink.If paper is accidentally torn during
29STATUS INDICATORSMISFEED REMOVAL Misfeed removalRoller rotating knobA. Misfeed in the paper feed area1Push gently the right side of the front cover
30STATUS INDICATORSMISFEED REMOVAL Misfeed removalRoller rotating knobFusing unit release lever2Turn the roller rotating knob in the direction of thea
31STATUS INDICATORSMISFEED REMOVAL Misfeed removal3Close the side cover by pressing the handle on thecover.●The misfeed ( ) indicator will go out.Misf
32GENERAL INFORMATIONUser programsUSER PROGRAMSThe user programs allow the parameters of certain functions to be set,changed, or canceled as desired.L
33GENERAL INFORMATION4Select the desired parameter using the right copy quantity( ) key.●The entered parameter number will blink on the right side of
34GENERAL INFORMATIONPOWER SAVE MODESThe copier has two power save modes to reduce overall power consumptionthereby reduce the cost of operation. In a
35GENERAL INFORMATIONSetting the power save modesThe time that elapses before the copier enters a power save mode after anyoperation is made can be se
36GENERAL INFORMATIONUser maintenanceUSER MAINTENANCEProper care is essential for clean, sharp copies. Please take a few minutes toregularly clean you
1GETTING STARTEDSTATUS INDICATORSMAKING COPIESGENERAL INFORMATIONCONTENTS PageGETTING STARTED●CAUTIONS . . . . . . . . . . . . . . . . . . . . . . . .
37GENERAL INFORMATIONCharger cleanerUSER MAINTENANCEUser maintenance1Turn the power switch off.2Open the bypass tray. Lift slightly on the side cover
38GENERAL INFORMATIONProblem Solution●Copier plugged in?●Power switch ON?●Copy density properly adjusted?●Is the original placed face down?●Paper to
39GENERAL INFORMATIONThe TD cartridge is not installed. Install theTD cartridge.Side cover is open.Close the front and side covers securely.The TD car
40GENERAL INFORMATIONSUPPLIESTypes and sizes of copy paperSize Weight Capacity Special paper(21 lb. bond paper)Paper tray 5-1/2" x 8-1/2" 15
41GENERAL INFORMATIONSUPPLIESGenuine supplies statementStandard supplies for this copier that are to be replaced by the user are copypaper, TD cartrid
42GENERAL INFORMATIONMOVING INSTRUCTIONSWhen moving this copier, follow the procedure below.When moving this copier, be sure to remove the TD cartridg
43GENERAL INFORMATIONType Digital copying machine, desktopCopy system Dry, electrostatic transferOriginals Sheets, bound documentsOriginal sizes Max.
44GENERAL INFORMATIONSPECIFICATIONSSpecificationsOverall dimensions 23-15/64" (W) x 20-23/32" (D)(with bypass tray folded) (590 mm (W) x 526
45GENERAL INFORMATIONAAuto clear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7Automatic exposure adjustment . . . . . . .
46GENERAL INFORMATIONSScrew . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11, 42Special paper . . . . . . . . . . . . . . . .
2GETTING STARTEDCautionsCAUTIONSFollow the cautions below when using this copier.●The fusing area is hot. Exercise care in this area when removing mis
47SHARP Date Issued:Nov. 1, 1998MATERIAL SAFETY DATA SHEETMSDS No. F-00841Section 1. Product IdentificationProduct:AL-160TD (Black Toner)Section 2. Su
48Section 6. Physical Chemical CharacteristicsBoiling / Melting Point: Not applicable Specific Gravity: 1.1Vapor Pressure: Not applicable Solubility i
49SHARPDate Issued :Nov. 1, 1998MATERIAL SAFETY DATA SHEETMSDS No. F-30841Section 1. Product IdentificationProductAL-160TD(Black Developer)Section 2.
50Section 6. Physical Chemical CharacteristicsBoiling / Melting Point: Not applicable Specific Gravity: about 7.3Vapor Pressure: Not applicable Solubi
51MEMO
WARNING:FCC Regulations state that any unauthorized changes or modifications to this equipment not expressly approved by the manufacturer could void t
PRINTED IN JAPAN99A KS➀TINSE0109QSZZAL-1600/AL-1610SHARP ELECTRONICS CORPORATIONSharp Plaza, Mahwah, New Jersey 07430-2135.SHARP ELECTRONICS OF CANAD
3GETTING STARTEDMain featuresMAIN FEATURESq High-speed laser copying●First-copy time is only 7.2 seconds (except in a power save mode or immediately a
4GETTING STARTEDPART NAMES AND FUNCTIONSOverall layoutPart names and functionsq Platen coverPlace the original on the original table and close theplat
5GETTING STARTEDPART NAMES AND FUNCTIONS!5 Drum cartridge handle Hold to pull out the drum cartridge.!6 Drum cartridgeCopy images are formed on
6GETTING STARTEDOperationpanelPART NAMES AND FUNCTIONSPart names and functionsq AUTO/MANUAL/PHOTO ( / / ) keyand indicators (p. 15)Use to sequentially
7GETTING STARTEDPART NAMES AND FUNCTIONS!2 Zoom keys (p. 17)Use to select any reduction or enlargement copy ratiofrom 50% to 200% in 1% increments.!3
Comments to this Manuals