Sharp CD-BA1700H Service Manual download pdf (Page 7)

– 7 –

CD-BP160W/180W/1500W/1700W

SETTING THE CLOCK

In this example, the clock is set for the 24-hour (0:00) system.

ON/

STAND-BY

CLOCK

MEMORY/SET

TUNING/

TIME

( )

Press the ON/STAND-BY button to enter the stand-by mode.

Press the CLOCK button.

Within 5 seconds, press the MEMORY/SET button.

Press the TUNING/TIME ( or ) button to select the time

display mode.

"0:00" → The 24-hour display will appear.

(0:00 - 23:59)

"AM 0:00" → The 12-hour display will appear.

(AM 0:00 - PM 11:59)

"AM 12:00" → The 12-hour display will appear.

(AM 12:00 - PM 11:59)

● Note that this can only be set when the unit is first installed

or it has been reset.

Press the MEMORY/SET button.

Press the TUNING/TIME ( or ) button to adjust the hour.

● Press the TUNING/TIME ( or ) button once to advance

the time by 1 hour. Hold it down to advance continuously.

● When the 12-hour display is selected, "AM" will change auto-

matically to "PM".

Press the MEMORY/SET button.

Press the TUNING/TIME ( or ) button to adjust the

minutes.

● Press the TUNING/TIME ( or ) button once to advance

the time by 1 minute. Hold it down to change the time in 5

minute intervals.

● The hour setting will not advance even if minutes advance from

"59" to "00".

Press the MEMORY/SET button.

● The clock starts operating from "0" second.

(Seconds are not displayed.)

And then the clock display will disappear after a few seconds.

To see the time display:

Press the CLOCK button.

● The time display will appear for about 5 seconds.

Note:

● The clock display will flash on and off at the push of the CLOCK

button when the AC power supply is restored after a power

failure occurs or after the AC power lead is disconnected.

If this happens, follow the procedure below to change the clock

time.

To change the clock time:

①

Press the CLOCK button.

②

Within 5 seconds, press the MEMORY/SET button.

③

Perform steps 6 - 9 above.

To change the time display mode:

①

Perform steps 1 - 2 in the section "RESETTING THE MICRO-

COMPUTER".

②

Perform steps 1 - 9 above.

(Main unit operation)

AM 12:00AM 0:000:00

(Continued)

■

AM/FM interval (span)

The International Telecommunication Union (ITU) has established

that member countries should maintain either a 10 kHz or a 9

kHz interval between broadcasting frequencies of any AM station.

The illustration shows the 9 kHz interval zones (regions 1 and

3), and the 10 kHz interval zone (region 2).

Before using the unit, set the SPAN SELECTOR switch (on the

rear panel) to AM tuning interval (span) of your area.

To change the tuning zone:

Press the ON/STAND-BY button to enter the stand-by mode.

Set the SPAN SELECTOR switch to "50/9" for 9 kHz AM

interval (50 kHz FM interval), and "100/10" for 10 kHz AM

interval (100 kHz FM interval).

Whilst pressing down the button and the X-BASS/DEMO

button, hold down the ON/STAND-BY button for at least 1

second.

● "CLEAR AL" will appear.

Caution:

● The operation explained above will erase all data stored in

memory including clock and timer settings, and tuner and CD

presets.

■

Connecting the AC power lead

Check the setting of the AC voltage selector located on the rear

panel before plugging the unit into an AC socket. If necessary,

adjust the selector to correspond to the AC power voltage used

in your area.

Selector adjustment:

Turn the selector with a screwdriver until the appropriate voltage

number appears in the window (110V, 127V, 220V or 230V -

240V AC).

Notes:

● Plug the AC power lead into a convenient AC socket, after

any connections.

● Unplug the AC power lead from the AC socket if the unit will

not be in used for a prolonged period of time.

● Never use a power lead other than the one supplied. Use of

a power lead other than the one supplied may cause an electric

shock or fire.

● AC Plug Adaptor

In areas (or countries) where an AC socket as shown in illustra-

tion ② is used, connect the unit using the AC plug adaptor sup-

plied with the unit, as illustrated. The AC plug adaptor is not

included in areas where the AC wall socket and AC power plug

can be directly connected (see illustration ①).

220V

Note for users in Australia and New Zealand:

An AC plug adaptor is not supplied if the lead has an Australian

Standard plug.

To an AC socket

1 2 3 4 5 6 7 8 9 10 11 12 ... 59 60

Comments to this Manuals

No comments

Sharp CD-BA1700H Service Manual Page 7

Comments to this Manuals

Related products and manuals for Cassette players Sharp CD-BA1700H